Basement Insulation

Stop already

EVERYONE...STOP ALREADY.......

Two things here....

1) the house is seven years old..It no doubt has the wall wrapped on the exterior..and will NEVER leak if it has not leaked to date!!! Given todays GOOD construction...I trust this stuff.

2) Secondly....the basement is already insulated to CODE.....unless you wanna make it warmer...leave as is....


Then....as I have done on three basements recently....


Just run the 2x3 around the room in front of the insulation/plastic. So much cheaper - faster...less work...less shit to throw in landfill....

Frame real good..throw in the wiriing / piping - and slap on some drywall. The basement is dry already..and there is enough venting and air movement behind that mold will never be a problem.

Just remember to use 2x4 on walls where doors will be...but otherwise I agree.

Wood is cheap now...cheaper and easier than metal in fact!

Lets not overthink this job...and not overprice it....especially if you plan on selling soon.

Yu should get all materials (minus flooring) for under 3 grand!! Easy!!
 
If I understand the picture your words describe, you're not supposed to insulate that gap at the top of the exterior wall and below the roof deck at the eave. It needs to be left open for ventilation from the eaves. They even make special styrofoam thingies to maintain airflow

Check out this link for better details. http://www.energystar.gov/index.cfm?c=diy.diy_attic_ventilation

I am aware of that and did that, however, there is not enough room between the top plate and the roof joists for anything but minimal insulation. I have maintained the ventilation as it is more important than heat loss.

There is a blocking detail in the current Residential construction guide that elminates this problem, however, in 1920, they built a brick wall, sat the 2 x 4 ceiling joists on top of the wall, then framed the hip roof with 2 x 4's as well. As a result, I can't insulate in their properly.

The walltight has about double the R value of Batt. I was figuring to install baffles to maintain the eave ventilation, then foam the attic.
 
I found a link from Alaska on how to deal with Ice-Dams. They recommended insulating the attic solid. After that, I vented the attic from the top, in such a way to gain appropriate airflow over the insulation. Worked like a charm on an 80 year old house.

Depending on the house construction, venting the attic through the eaves can be a really bad idea, and can cause severe problems. Same as adding insulation to a brick basement wall (as opposed to concrete). Older houses were designed to work a particular way. Techniques for new construction don't universally retrofit well.

Also, check out JTK's link: http://www.buildingscience.com/ It makes a great deal of engineering sense.

Attics never get insulated solid as far as I know. You need vents at both the eaves and ridge. The logic is that warm air rises, escapes from the ridge and that air venting out the ridge draws cool air in from the eaves.

Absolutely true about insulating old houses and old walls.

My house is 1920 with a rubblestone foundation wall. You cannot insulate rubblestone walls from the inside as the formerly warm wall will now freeze and the wall will crumble due to freeze thaw action in the mortar. I would even go so far as to say the same with even modern block walled basements. You should only insulate poured concrete (and concrete that is in very good condition) on the inside.

The best insulation for a basement is Rigid SM, however, you have to be very careful of the foam lapping any wood structure as termites tunnel right through the SM.

And yeah, building science is a fantastic resource isn't it.
 
Since you are finishing your basement, you're probably enclosing your furnace and water heater into a utility room. Make sure you have adequate combustion air intake.

Take a look at post no.3 in the link below.

http://www.homerepairforum.com/forum/hvac/5973-do-i-need-fresh-air-intake-furnace-room.html

Thanks to everyone for the information.

As mentioned I have had no leaks (touch wood). During the recent bitter cold spell the basement was comfortable (a little cool in bare feet).

I do plan on closing off the furnace and water heater. There is a vent about 5 feet from the furnace that goes right outside (similar to a dryer vent) and there is also one on the other side of the basement. I taped up the furnace piping with foil tape and covered the water pipes with foam.

For the floor, I plan on building the walls (a big open concept - no bedroom/den) first and then putting down Platon with 5/8 T&G OSB board. The Platon is similar to the plastic bottom of Dricore which allows water to flow through in the event of a leak.

I am now seriously leaning towards rubmeisters method of the sealant/mildew protection.

The house is a typical suburbian dwelling and I am not 100% sure of the exact external water-proofing, but have a good idea considering the age and common methods used. A couple of years back JTK mentioned in a thread to grade the ground in a downslope away from the house and I have had that in place for the past few years. I also use those plastic troughs to drain the eaves water about 3 feet out from the house.

Some interesting points about having a few drafts in a house. Growing up I remember we had drafts in certain spots in the house - However I cannot remember any instance of mold or experiencing that strong musty odour.
 
Just make sure you check with some real builders in regards to what they suggest. Home Depot doesn't hire knowledge like they used to when they first opened. I've heard one of their electrical "experts" referring to stove wire as "red-positive, black-negative, white-ground and the bare wire is just to help strengthen the cable". :)

That's pretty bad I have to admit.
In my experience they've been very helpful and knowledgeable regarding tiling and plumbing (Bathroom). (Argentia Rd Mississauga Location). If you need electrical help ask them if they have any electrical experience. Also if you read the instructions of the electtical appliance/device you bought, it'll tell you exactly how to hook everything up.
 
There is a vent about 5 feet from the furnace that goes right outside (similar to a dryer vent) and there is also one on the other side of the basement.

So these are just allowing air straight in to the basement? This would be a good place to save some energy....

Is your furnance a high efficiency model? If so, then it should already have it's own intake vent to the outside. I say should because the manufacturers do say you can just draw the air from inside, but that's such a waste to use nice warm air and throw it out the exhaust, not to mention a bad idea if you have an airtight house.
 
So these are just allowing air straight in to the basement? This would be a good place to save some energy....

Is your furnance a high efficiency model? If so, then it should already have it's own intake vent to the outside. I say should because the manufacturers do say you can just draw the air from inside, but that's such a waste to use nice warm air and throw it out the exhaust, not to mention a bad idea if you have an airtight house.

Yes it is a high efficeincy furnace. Come to think of it, I think they are vents that were put there for either a central vac or gas fireplace. The house has a gas stove, gas dryer and a gas line to the BBQ. They are round, galvanized with a screen on the outside end and about 6 inches wide.