Wood Laminate Flooring.

verbalks said:
I have not decided but I was given the task to clean up a house for resale (not in gta).

Old people lived in the house and they were at a stage in their lives they no longer cared about things. The old floor smelled and was ruined. I am just looking for a lower cost product with reasonably easy installation. It seems most want some form of wood in their homes over other products.

Since I am not planning long term with this house more expensive solutions are not viable since there is a ceiling as to what the home can resell for.

Well, you will always get 100% ROI when you install hardwood. As long as you don't go wacko and use bamboo in some funky pattern that is lol.

For the record, I can put down about 100 sq ft of click flooring in about 2 hrs and 100 sq ft of nail down in about 2.5. IMO if you want to really get the most bang for your buck, spend a little more on the front end and get either engineered or solid hardwood. Homo Depot has sales on all the time and I've seen asian maple and oak for as low as $2.99 psf. That's about half what you'd normally see and no, they aren't factory seconds. They are select or better quality.

Speaking of factory seconds. Do NOT buy it. It ain't worth it. In fact, I did a job this summer and quoted on it at my usual $3.00 psf install. Then they delivered factory seconds and easily 30% of it was garbage. Total crap. I even found different species in the boxes (I was laying ash and it had maple mixed in). After the job was completed I told the customer that I should have charged $10.00 psf for it because it took me twice as long. I also told the company that I sub to sometimes that from now on, if the job is factory seconds, my rate is $10.00 an hour.

Here's some problems with Factory Seconds:
1) Different species
2) Different stains
3) Different widths (one piece was 3 1/4 at one end and 3 3/8 at the other)
4) One box had what looked like 1 litre of black stain poured on the bottom pieces and the bottom two layers were totally unusuable
5) Large deep knots
6) extreme twisting of longer pieces (if you happen to get any)
7) Majority of the pieces were 16" long or less. Better quality flooring companies guarantee at least 50% of the pieces will be 36" or longer which makes for a nice easy install and a great random pattern.
 
kfames said:
Try not to leave too much of a gap at each end of the room as the wood will shrink dramatically in the winter, and small gaps may appear under the coping.

Don't put it to tight to the walls either....I have seen it expand and buckle.

I have laid many laminate floors and it is really easy.
I laid a beautiful hardwood floor this summer, I even got fancy and laid it all on a diagonal and added a inlaid boarder.

I am so proud of my handy work..:)
 
Molly Robinson said:
Don't put it to tight to the walls either....I have seen it expand and buckle.

I have laid many laminate floors and it is really easy.
I laid a beautiful hardwood floor this summer, I even got fancy and laid it all on a diagonal and added a inlaid boarder.

I am so proud of my handy work..:)

Man, I think I'm gonna change my name to "laminate floor" cuz then, maybe molly'd lay me too lol.

Diagonal......hmmmm not to take away but try and sell that to a propective buyer. The floor I did this summer too the customer wanted to do that but her real estate agent said it'd be hard to sell.

Borders in a contrasting colour are awesome. Did you use a router and template bit to do your inlay or did you just use a different hardwood?
 
Sasha Jones said:
X2
The only good thing I can say about laminate is that it is tough.
Other than that it is VERY loud and annoying when compared to real hardwood and if you look around you can find reall hardwood around the same price or even cheaper than a 'good' laminate.

Look at kultur in mississauga for one, we got ours there for around $6.85 installed, and that was for 5" wide the narrower stuff is cheaper and they have different finishes that vary in price as well. That was for real hardwood, the engineered stuff was even cheaper.
Just make sure to go to the warehouse in on Dundas, don't go to a dealer.


I shall check out Kultur in Mississauga. When I moved into the house it had brand new laminate in the entry way. It was $0.97 / sq ft Giant Carpet "cherry wood" laminate. The worst part of the laminate is the dirt.

Dirt gets between the cracks forms ridges. I tried scrubbing with a scrub brush. That made things worse. The ridges attract water and then the laminate begins peeling off, exposing the material underneath. This was after six months. I tried to find the same stuff, which naturally, Giant Carpet didn't have.

Also, I have to thank the poster who warned about affixing sliding doors to a floating wood floor. When I replace it I will have to make sure to drill into the substrate.

EU
 
Well EU: really, even hardwood and engineered shouldn't be used in wet areas. If it is just surface dirt/grit it should sweep right out. If you're getting it wet, well, you shouldn't. For that matter, you should NEVER scrub wood floors. At best you should only ever use something like a swiffer and if it ever gets wet due to spills or whathaveyou, then it should be wiped up immediately.

If you're replacing it you should put in a couple of rows of tiles (12" sq). This will give you a "mud spot" so you can remove your outside footwear.

As for the price, well, you know that old saying? "you get what you pay for..." and at $0.97 psf, you certainly didn't pay much.
 
Confused...

tboy said:
At least engineered hardwood (where they have a hardwood veneer on top, plywood base) or there are some better quality click hardwood veneer floors that have a man made substrate. Though for these you'll be paying 50% more than real hardwood.

Whatever you do in a basement, you'll have to use a vapor barrier underneath. This will prevent wicking moisture through the concrete slab into the flooring. Vapor Barrier Underpad is relatively cheap.

One of the things that make laminate floors so ugly is the fact that IMO all the boards are consistantly the same size and shape and you can easily see the cross seams. The higher end veneer click floors are random (just like engineered and solid hardwood) which makes it look more realistic.

As for durability: most engineered and solid hardwood finishes have a 20 yr warranty and IF you happen to gouge, scratch or ?? a board in the middle of the room, you can relatively easily replace it. It is infinitely more difficult to do this with click type floors (I've had to remove ALL the flooring to the damaged board then replace them all).
**********************************

A plastic vapour barrier over concrete? You're trapping moisture.

There's a product out that rolls onto concrete and allows air to circulate under the floor which is laid onto it. A plywood sub floor is usually put onto this product prior to finished floor application.
 
toughb said:
**********************************

A plastic vapour barrier over concrete? You're trapping moisture.

There's a product out that rolls onto concrete and allows air to circulate under the floor which is laid onto it. A plywood sub floor is usually put onto this product prior to finished floor application.

Hmm where did I say plastic???...but yes, many flooring manufacturer's vapor barrier does include a plastic membrane as well as a synthetic fibre pad.

As for trapping the moisture between the membrane and the concrete, so? Isn't that what you do when you use a vapor barrier when drywalling and studding a basement? (for the record, the answer is yes). There is no "air circulation" there either.

For reference a "floating" floor with the ability to allow air circulation is called Dri Core. It is an 24" square OSB product with plastic legs on one side that raises the floor above the slab. As for circulation though, if you finish the floor properly using baseboard and 1/4 round there is no "circulation". The moisture is still trapped under the Dri Core. It just isn't in direct contact with any absorbant material.

I have seen the "roll" type item as well and it is basically a plastic sheet with the legs formed in it. Again, there is no real "circulation" unless you leave the edges open and unfinished.
 
On all points I agree with you except...

tboy said:
Hmm where did I say plastic???...but yes, many flooring manufacturer's vapor barrier does include a plastic membrane as well as a synthetic fibre pad.

As for trapping the moisture between the membrane and the concrete, so? Isn't that what you do when you use a vapor barrier when drywalling and studding a basement? (for the record, the answer is yes). There is no "air circulation" there either.

For reference a "floating" floor with the ability to allow air circulation is called Dri Core. It is an 24" square OSB product with plastic legs on one side that raises the floor above the slab. As for circulation though, if you finish the floor properly using baseboard and 1/4 round there is no "circulation". The moisture is still trapped under the Dri Core. It just isn't in direct contact with any absorbant material.

I have seen the "roll" type item as well and it is basically a plastic sheet with the legs formed in it. Again, there is no real "circulation" unless you leave the edges open and unfinished.
********************************************

"As for trapping the moisture between the membrane and the concrete, so? Isn't that what you do when you use a vapor barrier when drywalling and studding a basement? (for the record, the answer is yes). There is no "air circulation" there either."

The answer is no!

The vapour barrier used in framing/drywall is there to prevent moisture from forming in your studs and causing damage as well as slowing down air leaks.

The concrete floor is porous and moister is already there no matter how dry it looks. A plastic or similar product traps that moister allowing mildew and unpleasant odours to form. A health hazard.

Wood flooring, in my and Mikes opinion, (name dropper) should not be laid directly onto concrete in a basement. Air must be able to circulate to cut down, if not eliminate moisture, caused problems.
 
toughb said:
********************************************

"As for trapping the moisture between the membrane and the concrete, so? Isn't that what you do when you use a vapor barrier when drywalling and studding a basement? (for the record, the answer is yes). There is no "air circulation" there either."

The answer is no!

The vapour barrier used in framing/drywall is there to prevent moisture from forming in your studs and causing damage as well as slowing down air leaks.

The concrete floor is porous and moister is already there no matter how dry it looks. A plastic or similar product traps that moister allowing mildew and unpleasant odours to form. A health hazard.

Wood flooring, in my and Mikes opinion, (name dropper) should not be laid directly onto concrete in a basement. Air must be able to circulate to cut down, if not eliminate moisture, caused problems.

Ummm so it is used to prevent moisture from forming in your studs....so where does it go once it wicks out from the concrete blocks in your basement walls? Magically disappears? Once you put up the insulation, stud the walls, vapor barrier and seal with tape, install drywall there is NO air circulation....EOS.

Yes, wood flooring should not be laid directly over concrete. That is why many floating floor installations use a underpad/vapor barrier first before installing the flooring.

You didn't answer my question as to how air is supposed to circulate underneath this "plastic sheeting" once you finish the walls and trim correctly?

Just because there is a void there doesn't mean there's air circulation....

Here's a direct copy from the Bruce Flooring Website:

Laminate can be used in any room of the house, below, on or above grade level. Laminate floors do have some sensitivity to excessive moisture, so if you plan on using laminate in a bathroom, you'll need to take special precautions.

While a floating floor eliminates the need to prep a subfloor, it does require the use of an underlayment. Underlayments provide protection against warping from moisture beneath, particularly if you're installing the floor over concrete. Underlayments also reduce or eliminate "hollow" sounds generated from traffic on the floor.

So, you're saying that one of the biggest flooring manufacturers in North America doesn't know what they're talking about?

Please........
 
Ok....

tboy said:
Ummm so it is used to prevent moisture from forming in your studs....so where does it go once it wicks out from the concrete blocks in your basement walls? Magically disappears? Once you put up the insulation, stud the walls, vapor barrier and seal with tape, install drywall there is NO air circulation....EOS.

Yes, wood flooring should not be laid directly over concrete. That is why many floating floor installations use a underpad/vapor barrier first before installing the flooring.

You didn't answer my question as to how air is supposed to circulate underneath this "plastic sheeting" once you finish the walls and trim correctly?

Just because there is a void there doesn't mean there's air circulation....
********************************************
Come on Tboy.

"so where does it go once it wicks out from the concrete blocks in your basement walls? Magically disappears?"

Your concrete wall do leak air and moisture. Concrete is porous.

If you've done it right there s/b no moisture. Old method was to use a tar paper material to seal the concrete wall. Today you move your studs out 2" and spray blue foam that seals the concrete as well as being a superior insulator.

"You didn't answer my question as to how air is supposed to circulate underneath this "plastic sheeting" once you finish the walls and trim correctly?"

There s/b no air circulation in studded walls. Have you seen how the vapour barriers are installed these days?

I hope this was useful.
 
Dude: so you're saying concrete is only porous on VERTICAL surfaces? By your statements it is ok to apply a vapor barrier and a water and air tight sealant (spray on foam) on the vertical walls but OMFG don't dare do that on HORIZONTAL surfaces because, that's BAD...LOL.

Dude, think about it then get back to me......
 
Tboy, what's your hang up...

tboy said:
Dude: so you're saying concrete is only porous on VERTICAL surfaces? By your statements it is ok to apply a vapor barrier and a water and air tight sealant (spray on foam) on the vertical walls but OMFG don't dare do that on HORIZONTAL surfaces because, that's BAD...LOL.

Dude, think about it then get back to me......
*****************************************

Everything I've written is chapter and verse from the building code, experience and professionals. If you don't accept that, not my problem.

Horizontal and vertical are treated differently in just about everything in life.

Your not wrong in most of what you say but have one hell of a time accepting something different/new or controversial, to you, and is now accepted building practice.

Have a drink and a good night!!!
 
Show me the code number where it states that you cannot place a underlayment with a vapor barrier on a concrete floor. TYVM. Until you do, I'll go with the manufacturer's specs.....

As for your professionals? Ahem, maybe they should learn how to do laminate flooring before telling you how they do it. See, the thing about it is, EVERY install I have ever seen for a floating floor over concrete includes an underlayment with a vapor barrier and every manufacturer states the same.

Who will I trust? Someone on an escort review board site or every flooring manufacturer in North America?

For the record: you said concrete is porous and breathes not me. Therefore by YOUR statement (not mine) there should be no problem putting a vapor barrier on a concrete floor because, as YOU said, it breathes.

If your concern (and it is YOUR concern not mine) is that you cannot put a vapor barrier on a horizontal concrete floor due to moisture becoming trapped, the same rule applies to encapsulating vertical walls. Only difference is on a vertical surface the moisture will pool at the bottom instead of spread over the entire surface.

Again: I ask you: please explain how you will get any air movement under your "dri core" type material if all edges are sealed via baseboard and quarter round?
 
Tboy, I think that you just like...

tboy said:
Show me the code number where it states that you cannot place a underlayment with a vapor barrier on a concrete floor. TYVM. Until you do, I'll go with the manufacturer's specs.....

As for your professionals? Ahem, maybe they should learn how to do laminate flooring before telling you how they do it. See, the thing about it is, EVERY install I have ever seen for a floating floor over concrete includes an underlayment with a vapor barrier and every manufacturer states the same.

Who will I trust? Someone on an escort review board site or every flooring manufacturer in North America?

For the record: you said concrete is porous and breathes not me. Therefore by YOUR statement (not mine) there should be no problem putting a vapor barrier on a concrete floor because, as YOU said, it breathes.

If your concern (and it is YOUR concern not mine) is that you cannot put a vapor barrier on a horizontal concrete floor due to moisture becoming trapped, the same rule applies to encapsulating vertical walls. Only difference is on a vertical surface the moisture will pool at the bottom instead of spread over the entire surface.

Again: I ask you: please explain how you will get any air movement under your "dri core" type material if all edges are sealed via baseboard and quarter round?
*************************************

to hear the sound of your own voice. If you don't get it now you never will.
 
toughb said:
*************************************

to hear the sound of your own voice. If you don't get it now you never will.

And I think while you like to post here sounding like you know what you're talking about, when challenged, you don't back up what you say....

Fair enough?
 
Is there an easy way to do stairs with wood laminate or is it best to use other products?

Any comments or tips would be appreciated.

Thank you.
 
I did the stairs in laminate. It wasn't easy. The couple that sold us the house did the floor. I spent about eight hours over two days doing three steps. Because obviously they thought it was too hard.

EU
 
The problem with doing stairs in laminate is that you can't nail it down to the existing steps, there isn't anything on edge to nail a bullnose to, and laminate is a bitch to work with because of the substrate being so full of resin, grit etc. I find laminate extremely hard on saw blades.

If the existing stairs just needed refinishing (and were already a hardwood such as oak) I'd consider sanding and staining them to match the new laminate. If that isn't possible (and you only had rough pine under carpet) I'd seriously consider doing the stairs in either a matching engineered or solid hardwood.

Stairs are another reason I hate laminate floors lol. In reality, if you buy a reputable enginnered or solid hardwood floor, you could effectively purchase milled stock and just stain it to match.

As I've said before: I HATE laminate floors and this is another reason why. To me, it's like those guys who used to buy the corvette kit for their volkswagen beetles. It just looks cheap.

This is wear I agree with Toughb and Mike Holmes: do it right the first time and don't cheap out. Remember: you'll get every cent back when you sell the house or ???....
 
tboy said:
The problem with doing stairs in laminate is that you can't nail it down to the existing steps, there isn't anything on edge to nail a bullnose to, and laminate is a bitch to work with because of the substrate being so full of resin, grit etc. I find laminate extremely hard on saw blades.

If the existing stairs just needed refinishing (and were already a hardwood such as oak) I'd consider sanding and staining them to match the new laminate. If that isn't possible (and you only had rough pine under carpet) I'd seriously consider doing the stairs in either a matching engineered or solid hardwood.

Stairs are another reason I hate laminate floors lol. In reality, if you buy a reputable enginnered or solid hardwood floor, you could effectively purchase milled stock and just stain it to match.

As I've said before: I HATE laminate floors and this is another reason why. To me, it's like those guys who used to buy the corvette kit for their volkswagen beetles. It just looks cheap.

This is wear I agree with Toughb and Mike Holmes: do it right the first time and don't cheap out. Remember: you'll get every cent back when you sell the house or ???....
Thank you for the advise. If the house was anywhere near the GTA I would "do it right" but the place is way up north and there is a small price range for home (Semi) 35K - 59K. :eek:

In addition to the floor being f***ed the kitchen was "downsized" and has to be reworked as well. So I have a limit budget. If it was my home I would what you are suggesting.

Thanks again for your helo.
 
verbalks said:
Thank you for the advise. If the house was anywhere near the GTA I would "do it right" but the place is way up north and there is a small price range for home (Semi) 35K - 59K. :eek:

In addition to the floor being f***ed the kitchen was "downsized" and has to be reworked as well. So I have a limit budget. If it was my home I would what you are suggesting.

Thanks again for your helo.

The kitchen was DOWN sized? Who the hell does that? That's fucked up....in today's market one of the top two renos is to INCREASE the kitchen size.....jesus. You've got your hands full there partner.

As much as I hate saying it (as I'm a custom cabinet maker) if you're looking for a cheap, "pretty" kitchen, the kits that homo depot sell aren't half bad looking. They are a pain to level and install because they don't have full backs on them and they have full gables not adjustable feet. I recently did a small kitchen install in a basement rental apartment and it didn't look half bad when it was done. They went with the maple melamine cabinets with maple doors and with some nickel plated pulls, it looked nice.

We also went with a butcher block countertop from Ikea. They sell an 8 footer for around $250.00 (and if you're looking to make a great workbench, it makes a great top for that too!). It was easy to work with because there was no backsplash (a new trend) and since it is an oiled finish, you don't have to worry about chipping a laminate.
 
Last edited: