C Dick said:So what is knob and tube anyway? How can you tell if your house has it?
Gentle Ben said:todays houshold wiring has the conductors all in one external casing, knob & tube was a system where the hot and neutral were seperate wires , and run through the studs & joists about 1foot apart from each other, where the wires passed through studs & joists there was a porcelain insulator(the tube) , the conections were made by twisting the wires together (the knob) , with no junction boxes,and no marrets,the connections were simply covered with cloth electricians tape. It wasn't really a bad system in its day IMO, but it was difficult to trace hot & neutral as both wires were normally black in colour, and there was no ground,
C Dick said:So what is knob and tube anyway? How can you tell if your house has it?
C Dick said:So what is knob and tube anyway? How can you tell if your house has it?
tboy said:LOL oh? how so?
Papi Chulo said:Device boxes may have a white & black wire that is spliced to Knob & tube wiring
http://en.wikipedia.org/wiki/Image:Knob-and-tubes.jpg
Also, some older non-metallic sheathed cable was cloth covered, which does not mean it is knob & tube
For Camera projects with a distance of less than 200 feet I use 18/2 stranded, for the power and RG59 for the video. You can get this in a single bundled cable at many suppy houses. As for the other project the 18 AWG would work well. 24AWG would be phone cable. You can go to a 22AWG by using bell wire, both of which are solid. I find the 18/2 stranded to be easier to work with.Anynym said:As a matter of curiosity, what gauge of wire would folks recommend for a couple projects I've got on the go?
One is a 24VAC surveillance camera (current draw is about 3.6W). For that, I'm currently using 14/2 (white Romex, rated to 300V) for the 24VAC, figuring overkill is better than cutting it close. That, and I couldn't find anyone at Home Depot to find me a more perfect fit.
The other application uses a 5VDC 3A power supply for an electronic project (involving two servos which in theory shouldn't draw more than 350mA each under strain). I'm looking at using a 24-gauge wire for that one (just a few inches of wire, not that that makes any difference), probably a little thinner than the wire on the power supply but not
as thin as the wires on the servos. Is 24-gauge likely to be too thin?
Any thoughts on what should be the appropriate gauge of wiring?
C Dick said:So what is knob and tube anyway? How can you tell if your house has it?
tboy said:LOL oh? how so?
tboy said:Well, if your outlets are all 2 prong is one indicator although that doesn't necessarily mean it IS knob and tube. If you have 3 prong then it 100% isn't knob and tube. One way to tell is remove one outlet cover and look into the box with a flashlight. If you see black and white plastic covered wires, the odds are you have conventional wiring. If you see cloth covered wires of any colour, you've got knob and tube.
Another easy way is to go downstairs into the basement and just look at the wires coming from the fuse box. If you've got a finished basement all the wires will be behind drywall but you should still be able to see the wires coming from the fusebox....again, if they're cloth covered, it's pretty much 100% you've got knob and tube.
Also, if you've got circuit breakers instead of fuses, you've been rewired unless of course some fuckwad put the money into a service panel for circuit breakers without replacing the knob and tube...(not sure if you can even do that.....though)
tboy said:OK, so that's your opinion...now sure, idiots could have been at the house, and idiots could have simply replaced all the recepticles and idiots could have spliced in romex into the knob and tube just 4 feet from the box...
so instead of saying how wrong I am, why not go all out and say the ONLY way to determine if you have ANY knob and tube in your house is to tear down every square inche of plaster/drywall? Because if your house is finished, according to you guys, that is THE Only way....
Well, it is funny, if you read my paragraph that you so rightly quoted, completely, then you'd see I said "if you pull off the recepticle cover, which you then reiterated, and you see cloth covered wires, then (I meant to say) you may have knob and tube instead of saying you have K and T.
Again, I'd really like to understand how I was way off base, when you wrote, almost word for word one of my suggestions? Maybe I wasn't precisely correct, but then again, neither are you! capice?
I replaced all my receptacles for cosmetic reasons.james t kirk said:Often times, people replace recepticles in their house for no other reason than they need to plug in an appliance with a ground prong. They have 0 intention of rewiring. It's not a case of being an idiot, they just want to be able to plug in whatever.
wrong, as has been pointed out already, many people could have 3 prong plugs with knob & tube,tboy said:Well, if your outlets are all 2 prong is one indicator although that doesn't necessarily mean it IS knob and tube. If you have 3 prong then it 100% isn't knob and tube.
tboy said:One way to tell is remove one outlet cover and look into the box with a flashlight. ............. If you see cloth covered wires of any colour, you've got knob and tube.
so at the panel end its pretty much 100% knob & tube, but at the receptacle end, "you've got Knob & tube?tboy said:Another easy way is to go downstairs into the basement and just look at the wires coming from the fuse box. If you've got a finished basement all the wires will be behind drywall but you should still be able to see the wires coming from the fusebox....again, if they're cloth covered, it's pretty much 100% you've got knob and tube.
way off base, many households have upgraded service panels without being re wired and it's totally legal.also there are tons of homes built without Knob & tube and using fuse panels rather than circuit breakers. My mothers house was post war time, most of the wiring in it isint grounded,the wiring is cloth covered over the plastic white & black conductors,and the outer wrap is cloth as well, it is not knob & tube, some circuits were grounded from original and other circuits were upgraded where needed, but many of the circuits are still ungrounded.The panel was replaced and the service was upgraded to 100 amp to accomodate an electric drier some years ago, the drier circuit & service panel was inspected at the time of install. nothing was mentioned about the non grounded circuits, the only thing the electrician had concerns on was, an extension cord that my Dad had run through the joists to his workbench, it would have been considered a permanent installation by the inspector, a definate no no, so Electrician ran a proper circuit to the workbench at that time, so yes, it was inspected too.tboy said:Also, if you've got circuit breakers instead of fuses, you've been rewired unless of course some fuckwad put the money into a service panel for circuit breakers without replacing the knob and tube...(not sure if you can even do that.....though)
Gentle Ben said:wrong, as has been pointed out already, many people could have 3 prong plugs with knob & tube,
wrong, there was cloth covered wiring that wasn't knob & tube, see below
Gentle Ben said:so at the panel end its pretty much 100% knob & tube, but at the receptacle end, "you've got Knob & tube?![]()
As I corrected in a subsequent post, I said I should have added possibly.....
Gentle Ben said:way off base, many households have upgraded service panels without being re wired and it's totally legal.also there are tons of homes built without Knob & tube and using fuse panels rather than circuit breakers. My mothers house was post war time, most of the wiring in it isint grounded,the wiring is cloth covered over the plastic white & black conductors,
Since everyone is being so picky, I might as well be too.... The above quote only supports my statement that if you look in the box which the duplex recepticle is mounted to and see CLOTH covered wires, (as I corrected in a subsequent post) you most likely have knob and tube. If you look in the box which the duplex receptible is mounted to and see black and white plastic coated wires, you most likely won't have knob and tube.
But as stated by someone else, some idiot may have pulled out all the boxes, pulled out all the recepticles and switches, pulled out 24" of knob and tube cables, spliced in 24" of romex, pushed the whole lot back into the wall, reinstalled the box, reinstalled the duplex recepticles and switches....
So, as I said before: the ONLY way to tell if you have ANY knob and tube, is to remove ALL the drywall in your house and examine ALL wiring and just thinking again, because you all are being so picky about this topic, you shouldn't have to remove ALL the drywall/plaster and lath, you only have to remove enough to find all the wire runs. Because hey, who knows? Someone might have replaced or updated only half the circuits and left one length of K and T somewhere....
The above is only applicable if your house is older than 1940's....but as I've read on another thread, it could be present in houses 50 yrs old which would make that K and T were used in the 50's as well.
SO, all you people who are posting all the possible scenarios for the possibility of knob and tube, if you're going to correct me, at least do it correctly and list ALL the possible scenarios where knob and tube might be present instead of just a few.
I correctly pointed out some simple quick checks to see if you might have knob and tube wiring.
If you want to start splitting hairs, and obviously you do, then you also might want to include the possibility that some idiot might have pulled out all the non metallic sheathed cable or romex and installed knob and tube in it's place.
In fact, just to take it one step further, some idiot could have bought a house last week, which was completed the week before, and pulled out all the romex and installed K and T in it's place.
papasmerf said:If you are unsure of your wiring, hire a licensed MASTER ELECTRICIAN. If you are unsure of their qualifications, hire a union contractor.