Any electricians here?

Status
Not open for further replies.
tboy said:
static electricity produces no current........which can be produced relatively easily using a van der graf generator.


It does not produce no current.

It produces static electricity, or electricity at high voltage and low continuous current.
 
james t kirk said:
....You'd think then that she'd have the place rewired (after the insurance company repaired the 2 rooms where the fire was). But no, a trip to Thailand was more to her liking than proper wiring...

I don't think insurance companies will write new home policies on knob and tube anymore. They usually want all the wiring upgraded.

LordLoki said:
... Also your house insurance will not pay out for any damages because you contributed to them....

Most home insurance will not pay out:
(1) if you made any changes to home wiring that were not inspected.
(2) if it was caused by a non CSA/UL approved appliance (euro stereo)
(3) if you made any changes to a CSA/UL approved appliance (new plug)
 
Last edited:
Papi Chulo said:
It does not produce no current.

It produces static electricity, or electricity at high voltage and low continuous current.

Ok, it produces current so low as to not pose any type of threat or danger through electrocution methods.....
 
Actually in this case not static electricity. 2 wires, needed to complete the circuit to feel anything. But correct, very low current, huge voltage. Also 45 to 80 hz is ideal for stopping hearts. BDSM toys run at much higher frequencies ( or static charges as you mentioned).
 
data1960 said:
...So we all agree - he should buy the $10 step-up transformer. He should not mess with his house's wiring (he should hire a pro) and Kelli at CB is gorgeous.

I think he can pick these transformers up for cheap in FTA alley (Dixie and Matheson) and visit CB afterwards to spend all that money saved on electricians.

It's a lot cheaper than rewiring a plug or trying to convert that stereo to 120. Also, he can move the whole thing into another room or house at a later date. If he has a special 240 VAC receptacle wired for him, everything will be stuck in that room.
 
l69norm said:
I don't think insurance companies will write new home policies on knob and tube anymore. The usually want all the wiring upgraded.



Most home insurance will not pay out:
(1) if you made any changes to home wiring that were not inspected.
(2) if it was caused by a non CSA/UL approved appliance (euro stereo)
(3) if you made any changes to a CSA/UL approved appliance (new plug)

I bet 80 percent of the houses in the old part of Toronto, if not more, have some, if not A LOT of active knob and tube.

I think it depends...

1. If you are part of a group plan - my friend (and I) are, therefore, they rate you as a group and it would be very hard to turn someone down. In my friend's case, she is a teacher and her house had an electrical fire (verified). The insurance company - Johnson's repaired the damage, but did NOT insist that she rewire the rest of the house (I couldn't believe that), nor did they raise her rates (I couldn't believe that either)

2. If you have been in the house a long time, since before the insurance companies cared about knob and tube, your policy is grandfathered. Heaven help you if you drop it for some reason.

3. In my case, when I bought this place, it was full of knob and tube. I have subsequently rewired 95 percent of the house myself and it will be 100 percent when I do a little reno in the spring. All my insurance company cared about was that I had a modern panel installed. They sent a guy to my place, he looked at the shiney new Siemens panel, said, "that's great" and walked out the door.

4. There are lots of people who have knob and tube and don't even know what the hell that means. My neighbour had thought that most of the knob and tube was out of his place and he recently was shocked to find out that other than a butcher job in the basement and kitchen, it was all pretty much still hot.
 
data1960 said:
LOL. How do you come to know that? Not doubting you, but that is a weird thing to know! Should I be scared of you?


All in the good old loss control manuals. A few thousandth of an amp across the heart muscle of 60 hz juice can put it into fibrillation. When I was young and foolish the rage was Violet Wands for BDSM play. They creat a relatively safe static charge that could be used for the most interesting reactions. Danger was if the internal mechanism shorted through the line voltage could be applied to the subject. Low probability but serious problem with 60 hz finding its way to ground through your torso.

There was also a problem with wax core capacitors and coil insulation in them. (Safety tip: If you play with a Violet Wand get a GFI ! If you do not know what a GFI is do not play with a Violet Wand)

Resent electronic/electric toys use a DC to high frequency AC circuit. Different effect, and needs two wires but rather interesting. Again very low amps, very high volts, and avoid the 60HZ range. (Yes I know some plug into the wall, that part is a transformer that provides the DC voltage).

So how do I know? I have always been rather fond on my lovers and would be very annoy if one died while we were trying for the perfect orgasm. So if you are going to play, learn first. Also my tricks involve putting one plate on her, one on me, and making certain I am part of the circuit. So I can tell exactly what she is feeling. Could make me dead if I was an idiot.

Scared of me? Nahhhh I am a pussy cat.
 
Is it just me or does it seem like there is an awful lot of electricians on terb?
 
Papi Chulo said:
Is it just me or does it seem like there is an awful lot of electricians on terb?

even more techs
 
LordLoki said:
(Safety tip: If you play with a Violet Wand get a GFI ! If you do not know what a GFI is do not play with a Violet Wand)

Thanks for the tip!

Question...would there be any added danger if I would to install the metal probe instead of the glass one, hold it in my right hand and use my left hand as a probe while the current flows through me?
 
james t kirk said:
I bet 80 percent of the houses in the old part of Toronto, if not more, have some, if not A LOT of active knob and tube. I think it depends....

I seem to remember that if knob and tube shows up in the paperwork for a home resale, the insurance company wants it removed and you would need to factor it into the negotiated price. It's about $1,200 per room. No insurance = no bank mortgage = no sale. It's the same for an oil furnace/ underground tank.

Maybe one of the TO real estate guys can confirm?
 
I know of atleast 3 people that have had to remove knob&tube to satisfy insurance company, in one case it was an elderly couple, on wait lists for old age home as health had deteriated, Ins. Company didn't care that likely within 6 months they would be moving & eventually selling the home, basically, no upgrade to the wiring, , no insurance
 
Gentle Ben said:
...in one case it was an elderly couple, on wait lists for old age home as health had deteriated, Ins. Company didn't care that likely within 6 months they would be moving & eventually selling the home,...

The insurance company's (bad) logic is that the house will be worth more when the old couple sells it, so they should recover what they spent and not be out of pocket.
 
As for replacing knob and tube: if the guy knows what he's doing, it can be pretty easy and cheap to do (and if he's lucky). One time I was working on a house and the sparky lucked out by having a framed in stack that ran from the basement, right beside the service panel, to each floor. A couple of holes in the walls to patch at the top and where the boxes were to go, and bob's your uncle. And yeah, the knob and tube was patched into all over the place.

One thing to mention too about knob and tube replacement is that the boxes and recepticles will all be replaced as well with grounded units. Saves homeowners from cutting off the third prong on all their plugs.....
 
before you use that eqipment, you should make sure it has either a CSA or UL approval. If you hook it up and it causes a fire, you can forget about an insurance claim. As for hook up, you could always hard wire it to a disconnect switch, just make sure you have overcurrent protection (fuses or circuit breaker). Your big problem is the 50 Hz. Some equipment will run on 50 or 60 Hz just fine, some might work, but not as effeciently. I hope that helps.
 
data1960 said:
Assuming you bought through a realtor, did they disclose the aluminum wiring?

They did disclose the aluminum wiring, but I did nor realize the implications, I knew nothing, I just thought it was another kind of wiring. Then when I found out about the hazards, I was upset. But when I researched more, and found that it was just a matter of handling it properly, it was not so bad.

Our house inspector found all the bad things, but we bought it anyway.
 
Section 4-004, except for flexible cord, equipmen, control and cable conductors shall not be smaller than 14 ga if copper and 12 ga if aluminum. This rule applies to wiring of buildings. Equipment wiring is regulated by CSA, not the CEC
 
Status
Not open for further replies.