Vinyl Sign stand

Maxie

New member
Feb 6, 2006
140
0
0
I have a 20ft wide vinyl banner sign. How can I get it to stand on its own for a display without having to buy an expensive stand. I can't put stakes into the ground for this project. I'm not that handy so any design would have to be simple. I was thinking two poles on each end fastened into something sturdy on the ground where the sign has to sit. A simple solution using some supplies from Home Depot would be good.

Thanks
 
1) You didn't say how tall it was so I will have to assume it is around 8 ft.
2) Does it have vent flaps cut into it? You know, those little semi-circle shaped cutouts to let air flow through....
3) Does it have any grommets punched into the edges and are the edges seamed?
4) What gauge is the vinyl?
5) How long does it have to be up for?
6) Why can't you put stakes into the ground? Is it on pavement or concrete?
7) How "pretty" do the supports have to be?

Whatever your answers to the above, you will have a problem keeping it upright if it is the slightest bit windy. You've got quite the sail area there....

You will also have to put guy wires into whatever uprights you use to keep the banner taunt over it's length. You will need a minimum of 3 at each end.

If it doesn't have wind vents I'd cut at least a dozen slits into it with a really sharp utility knife. Make them about 6" long each.

If I were you I'd try cast iron/steel pipe, at least 1" dia, and at least 2' longer than the banner is high. You will have to drive them at least 2' into the ground else they will blow over. I'd use 1 at each end, plus 2 spaced evenly in the middle. I'd also purchase some aluminum aircraft cable to use as guy wire, some turnbuckles for tension, and 12" spikes to set the guy wires.

If the ends do not have tunnels sewn into them you will have to figure out a way to attach the banner to the poles. The easiest way would be to use grommets and nylon wire ties. The wire ties would also help keep the banner taunt along the length of the poles.

Since you say you can't drive anything into the ground, you will have to buy bags of concrete, sand or gravel to weigh down the supports. Even still, you will have problems with this banner blowing over. Especially if we get some of our normal 40 - 60 kph wind gusts which is the norm for this time of year.

If you want, pm me and I will quote on putting it up for you.
 
tboy said:
1) You didn't say how tall it was so I will have to assume it is around 8 ft.
2) Does it have vent flaps cut into it? You know, those little semi-circle shaped cutouts to let air flow through....
3) Does it have any grommets punched into the edges and are the edges seamed?
4) What gauge is the vinyl?
5) How long does it have to be up for?
6) Why can't you put stakes into the ground? Is it on pavement or concrete?
7) How "pretty" do the supports have to be?

If the ends do not have tunnels sewn into them you will have to figure out a way to attach the banner to the poles. The easiest way would be to use grommets and nylon wire ties. The wire ties would also help keep the banner taunt along the length of the poles.
The sign can sit about 8ft off the ground.

I'm using a piece of thin stretchy vinyl from fabricland. How can I make four holes at each corner without the sign ripping, or could I staple the sign around two poles? I was going to have someone hold the sign on each end while sitting or standing.

The display is meant for a few hours.

The supports don't have to be pretty but I can't put stakes into the ground because of concern for a sprinkler system.

tboy said:
you will have a problem keeping it upright if it is the slightest bit windy. You've got quite the sail area there....

If it doesn't have wind vents I'd cut at least a dozen slits into it with a really sharp utility knife. Make them about 6" long each.

Even still, you will have problems with this banner blowing over. Especially if we get some of our normal 40 - 60 kph wind gusts which is the norm for this time of year.
Good tip, whatever design I go with cutting some slits so the wind can blow thru is a good idea.
 
Maxie said:
The sign can sit about 8ft off the ground.

I'm using a piece of thin stretchy vinyl from fabricland. How can I make four holes at each corner without the sign ripping, or could I staple the sign around two poles? I was going to have someone hold the sign on each end while sitting or standing.

You could go to Home Depot and get a cheap grommeting kit. Fold the corner over onto itself and then put a grommet in. When you say "thin stretchy vinyl" vinyl generally isn't stretchy, it is flexible, but not stretchy. Lycra/Spandex is stretchy... You may have bought something other than vinyl. Is there a texture (even a slighty texture) to the material? Are there fibres woven into it? Sometimes plastic materials have strands impregnated into it for reinforcing.


Maxie said:
The display is meant for a few hours.

The supports don't have to be pretty but I can't put stakes into the ground because of concern for a sprinkler system.


Good tip, whatever design I go with cutting some slits so the wind can blow thru is a good idea.

Depending on what material you actually have and how thin it is you may have to seal the edges of the slits to prevent them from running or tearing after you make the slits. You could use something like nail polish or cement to coat the edges.
 
tboy is steering you right. Not to put you off, but there's a bit more to it than appears.
In no special order:
1) If the top of tha banner's at 8' then the bottom edge is in the 'idiots can walk into it and vandals can destroy it' zone. You must give thought to making safe.

2) You should know that the tension along the banner increases as you pull to take the sag out, and will become infinitely great if you manage to eliminate all sag. Of course, a stake will pull out or, a guy will break or the banner will rip long before that. Run a rope, wire or string through a tunnel hem along the top edge or use something like curtain rings or lacing to hang it from a "clothesine" that can take the strain. Besides, that way you get the poles up and secure before you start dealing with a "sail" that you probably don't want to ever touch the dirt. Take a stepladder.

3) Allow for a minimum of two guy rope/wires at each pole, so the pole and the two guy anchors make the biggest triangle possible. Better would be two guys anchored directly front and back of the banner and a third providing the stretch outwards from the end. Don't forget to put flags on the guys to warn people of the tripping hazard

4) Your guys will tend to drive the poles into the ground. Best provide some sort of plate or foot to prevent it, or it will all go slack. Do not use plastic pipe, because once you stop it from driving into the ground, it will demonstrate its bendiness.

5) Make sure you have the space; 20' of banner plus 8' minimum at each end to anchor 8' poles is 36' (more is better, the steeper the angle of the guy, the less it's pulling horizontally, and that's what you want)

6) If you're not going into the ground, and using something like water-filled garbage cans/oil drums ( anywhere up to 400lbs), or bags of cement (app 70lb ea) as anchors, then aircraft cable is overkill (Sorry to disagree, tboy) and it's annoying to fasten. Basically any rope that can lift whatever anchor weight you're dealing with multiplied by three should be plenty—but remember 2) above, even the aircraft cable will snap before it goes dead horizontal—and you can knot rope. You do have a Boy Scout handy by, I hope.
BTW: 20+(4x8)=52 ft, plus 10x2 for knots =72' total for the minimum set up. Yellow polypropylene is cheap and strong, use a Bic lighter to melt the ends and keep it from unraveling; the hollow braided stuff that floats (think water-ski rope) holds knots better. Don't skimp.

7) Final thought, now I've made it so forbidding. Think clothseline with three or four sheets hanging from it. That's what you're setting up. And the technology's all available at you hardware store, along with plastic press in grommets, so fear not. Just don't go light on those anchors.

May you have a banner day.

PS. Think of rain. Make sure your banner's waterproof.
 
Wall mount the sign.

Use many grommet holes on the edges of the vinyl, like one every two feet.

You'll have to drill anchors into the wall to attach to the grommet holes.

Good to go.
 
tboy is right. So many outdoor banners are taken down because of the wind.

If it's not a must for 8' high, borrow 2 Outdoor collapsible umbrellas with the cast iron base or water base.

Otherwise, rental a volleyball pole set and security them with two cement blocks, the ones with cell opening big enough to put the poles into. Not sure if the beaches sport rental stores have them in stock considering out of season. Some schools have huge cast iron base for volleyball/badminton poles.

Pro Photo equipement stores rent lighting stands but for 20' sign, need the expensive high end stands and not 8'.
 
goodtime said:
with the cast iron base or water base.

pole set and secure them with two cement blocks, the ones with cell opening big enough to put the poles into.

cast iron base for volleyball/badminton poles.
Can I hand make a heavy base that can secure a pole on each end, maybe two large sized flower pots filled with soil or something sturdier, cement is too heavy?
 
Maxie said:
Can I hand make a heavy base that can secure a pole on each end, maybe two large sized flower pots filled with soil or something sturdier, cement is too heavy?

Find out where the sprinkler system is and then go into the ground.
You can buy 4x4 holders (metal with spike) that can be banged into the ground. Use 4x4x8 or 10 lumber and they will never tip over.
 
I can buy plastic umbrella table base holders for 10 bucks, fill them up with water or sand, and put a 1.25 inch diameter wood pole in them. Will that hold steady a sign 15-20ft wide for the day assuming the weather isn't too bad?

For the sign factory cotton which is cheaper than vinyl was recommended? a tailor could sew the ends to fit over the pole. Water based (waterproof?) acrylic paint was recommended.
 
If there is a sprinkler, you would think that there would be trees and / or a house. Then you can tie your rope up high and not have to worry about posts or guy wires or anything. Decent sized trees are ideal.
 
Cotton is much lighter than vinyl, not cheaper. Know a buddy that does it on the side.

Don't waste time with pots unless you use concete. Depends on how windy, make sure you can get close to 4" into the base or have picnic tables to help counter from tip over.

For light cloth signs, we used rope across two canopies to attract attention and keep us out of the element.

Have a good event.
 
Plan B

I put in a good effort, but two base weights with a pole on each end isn't strong enough to hold thin vinyl fabric without it drooping across any length past 7ft or so. I'd like the sign to be at least 8ft wide and 3ft tall.

Plan B: Corrugated cardboard 8 by 4, it seems to fold ok to fit in the car without much damage to the sign upon being spread open for use. I'll staple it to the poles maybe and cover it with plastic in case it rains.

(I'm quite pleased with the heavy duty Mastercraft staple gun bought at CTire for $20.)

What do you think, any other ideas?
 
Hire 20 fat guys to stand side by side without shirts, paint your message on their bellies. This should get some attention.

Cost - 20 boxes of day old donuts and a can of paint should be less than a hundred bucks.
 
Maxie said:
What do you think, any other ideas?

Just hope the wind does not exceed 5 km/h.

You may want to reinforce the cardboard with thin wood strips in the back. You can staple the cardboard onto the horizontal wooden strips before you put your graphics on. You should be able to get these strips from lumber places for nothing or next to nothing.
 
We keep telling this guy what to do and he keeps asking for more....

Maxie: Just do it (as the Nike ads once said).....

Just remember: Sign and Banner companies do this all the time and charge about $2000.00 for the banner and stands. Why do you think they charge that much? Cause it ain't easy to get a banner that large to stand on it's own. Then factor in transportation costs etc. and you're getting up there.

If you want it done for $100.00, it ain't gonna happen cowboy.

I even did up an autocard drawing for him of a way to do it for less than $100.00 in materials but he wouldn't give me his email so I could send it to him....
 
check your pm tboy

One Solution: I bought a thin piece of cardboard type wood for 10 bucks, it has a white backing, cut it in half to make two pieces 8ft long by 3 so the sign will be about 16ft wide once I nail it together in the middle with a piece of scrap wood. The sign big enough to get attention would sit on the ground leaning against the legs of two people on chairs.