Speaker wiring for a audio system...

BiggieE

Guest
Jan 29, 2004
609
0
0
Rochester, NY, USA
Does anybody here know if there are any benefits to bi-wiring an audio system. The dealer I bought my new speakers from has suggested it, but I'm not sure if it's worth the money to do it. Any input is more than welcome.
 
A lot of people swear by it. Personally I found a marginal difference with bi-wiring. (Not that I expected a hugh difference mind you). To me, bi-wiring is the really nit-picky fine tuning of an audio system. If you've concentrated on the proper matching of the various components, then bi-wiring is probably the last thing you deal with. Even then, if you don't do it you might not miss much.
 
I bi-wire on one of my systems... primarily because routing was difficult and whenever I route in difficult situations, I route two :-)

I really do not think you will notice any difference. I am also against mucho expensive cables (I have one set of nice cables... for the rest I either use quality 12ga or home depot extension cord cable... the latter is really cost effective for long runs, and sounds decent).

I would put money into room treatements or eq before I ever put it into bi-wiring.
 
Just took a look at the schmatics of bi-wiring. If you decide to use this. you sould use speperate cables, both shielded and the shields tied to refrence ground at near end (amp). and taped off at the far end(speaker). The most important thing as previously stated is good matched equiptment. Over the years while the toys have changed, the basics have not. A 20hz to 20Khz or better is still a good base standard. THD always bad. The smaller the number the less effect it has. Total output of your receiver or amp is expressed in RMS and often is the sum of the out put channels. Therefore a 200 watt unit might well be expressed at 50 watt rms per channel for 4 channels. Contrary to what the salesmans says you do not use 200 watt speakers, when this is the case. you will not be able to use them at less than about 30% power or 3 on the volume control. When you have a speaker with such a higher value than the power output of the system, it sounds "flat" at low volumes. At 50 watts per channel you would need about 71 watts per speaker to handle the peak power the channel might send. So likely you would get 75 or 100 watt speakers. You will see a major sound improvement when you used matched speakers and a too frequencey Response on the speakers and amp.

As for the bi-wiring? Based on what the schmatics show I would see that as no gain when you use a typical speaker cable.
 
Papasperf: Preciesly. Maximum power thansfer occurs when the output impedance is equal to the input impedance. It is important to note that half of the power will be dicipated in the output section of any amplifer when impedance is matched.
The monster cables to me a re a joke. The capacitence of standard 12ga home wiring (romex) is so small at audio frequncy, it , to me makes no sense.
What is this term, bi wiring?
Simple parallel cables between Amp and Speaker?
 
I stopped by the dealer yesterday to talk about bi-wiring. They claim an improvement in clarity, and imaging.The cables need, to match the ones I have on my system were all of $30, so I decided to give it a try. My Amp/Speaker combo is an Adcom 5802 power amp, and B&W 704 speakers. So far, the jury is still out, but I have noticed an improvement in imaging, though the clarity seems the same. I guess for $30, it was worth a try.......
 
Just make sure that you put the red wire in the red input and the black wire in the black input.
 
I bi wired my speakers with van den huls and honestly there is no real apparent difference, whereas the difference was huge when I upgraded to the single run of VDH. I'd highly recommend putting the $ into the shortest run possible of better cables, as the results can be as good as buying a new component.
 
Diode said:
What is this term, bi wiring?

Bi-wiring means that you have separate leads going from the amp to the high frequency section of your speaker and to the low frequency section. Very high-end amplifiers have separate posts so that you can run compeltely separate wires to the different sections of the speakers. i.e. Instead of 2 posts on the amp going to 4 posts on the speaker, you have 4 amp posts going to 4 speaker posts. Normal, consumer-grade speakers of course only have 2 posts.

Here's a good bi-wiring basics: http://www.st-andrews.ac.uk/~www_pa/Scots_Guide/audio/biwire/Page1.html
The typical bi-wring arrangement is shown in figure 2.
 
At $30 for 12 feet of cable, I don't think my dealer is going to be vacationing in the Bahamas anytime soon. So far, I do seem to notice an improvement in Imaging and clarity. btw....the amp I'm using is an Adcom GFA-5802 and the loudspeakers are Bowers & Wilkins 704s. So far I'm rather impressed.....I'm thinking about a Universal Digital Player next. I'd like to try out the DVD-A, and SACD formats, but I don't really want to shell out $4,000 for a player....
 
You paid $30 for only 12 feet of cable?

I think I know your dealer.... your right he's not vacationing in the Bahamas..... he's the guy at the table next to me in a Bangkok bar with 4 girls taking turns sucking his cock while he laughs and tells me of how he sells over priced speaker wire.

http://www.lolitasbangkok.com
 
zzap said:
You paid $30 for only 12 feet of cable?

$30 for 12 feet is not much in the world of high-end audio. MIT and Transparent Cable both easily run into the thousands. It's not unheard of to spend more than $5000 (Canadian) for a pair of 2.5m speaker cables. Obviously this represents the ultra high end of the market. But some people will spend $20K (each) on the amps and another $20K on the speakers ... well, you get the idea.

Mind you, at those prices someone is vacationing in the Bahamas for sure!
 
My current CD player has twin burr-brown Class A D/A converters....I had thought about that, but I don't think I can do much better than that....Who would'nt love a set of Wilson Watt-Puppy speakers....but at $40,000 a pair, I'm afraid they a bit out of my league.....
 
xarir said:
Why don't you spend the $$$ on a good D/A converter instead? For audio you can't beat it.

You cannot use a d/a converter with the higher rez formats other than some "special" firewire links I believe. I believe the best combination is a mod'ed SACD player with a non oversampling DAC. This is currently what I run, and is a nice combination.
 
Does anyone have a mulitzone audio system (whole home audio) installed in there house?

Is it worth it?

I have access to a product (at a decent price) that I saw in a few high end homes and was thinking of installing it in my house.
 
so called

zzap said:
I think it's just a way to get you to buy more speaker wire.
Who said anything about wire ? : )

http://www.vandenhul.com/cable/thrd.htm

http://www.e-speakers.com/products/vdh.html

It's funny, but I see it as those who aren't aware of the potential in cables as being the ones who have "the wool pulled over their eye"s, or more correctly are just unaware. However, you are right, zzap, in that, they are the ones who will be left with more $ in their pockets - not I. Sure you can put a couple of hundred dollars more into actual components, but you won't get much more superior sound for whatever small percentage of your individual components the price of cables/interconnects is. Besides, what's the point if you're not going to fully realise the potential of such components anyway.

Daddyo said:
Does anyone have a mulitzone audio system (whole home audio) installed in there house? Is it worth it?
That all depends on the quality of cable :þ

Seriously, cables can make a huge difference. I have Vdh carbon interconnects and hybrid speaker cable. The interconnects made a huge difference alone. I even tried them in so called low fi stereos and they made a significant difference ( smoother treble/mids, tighter base and more coherent detail in general ) Upgrading from monster speaker cables made another significant leap in sound quality. The VDH 2nd's are awesome interconnects [especially for SS] and the VDH C-122 is amazing speaker cable for the price and can be found used on www.ebay.com or www.audiogon.com relatively cheap.

My whole fascination with stereo equipment evolved when I bought so called better cables and added them to my then, "low-fi", stereo system. Not all cables will have the same effect and these particular ones which were pretty cheap were too revealing. All they did was let me hear how horrible my source in fact was, as well as magnify the head-drill highs. At least, that's my interpretation and perception. I have however found pretty cheap cables that do improve/ focus the sound. For instance I have a $30 [abt 10 years ago] pair of 'Ultralinks' between my DVD player and TV - they also tighten bass and bring out the detail in mass market systems without emphasising the mids highs - the difference is not subtle.

Anyway it's not an exact science and I could debate with myself on my perception, however what you hear is real - it's just defining it that can be confusing.
 
Last edited: