Putting on Winter Tires Soon

homer

Well-known member
Aug 18, 2001
16,326
107
63
Hello!

Just a quick, probably stupid question about my Venture van? I finally bought a hydraulic bottle type jack so I don't have to use the crap screw type one that came with the van. I do have one question please? Once I raise up the vehicle , where is the best place to put the jack stand? I know, probably a stupid question, but I was hoping to get a suggestion from someone way more knowlegable than me, before I do something that damages the car. Thanks again for the help!

Homer
 
Depends on whether the van has a frame or is of "uni-body" construction.

If it has a frame, you need to put the jack stand directly under the frame, just behind the wheel somewhere, on solid ground.

If it is a unibody, you need to put the jack stand under the sill (the part of the body under the door) again right behind the wheel.

The best bet would be to read the owner's manual and see where it says to jack the vehicle from.
 
Hello!

Just a quick, probably stupid question about my Venture van? I finally bought a hydraulic bottle type jack so I don't have to use the crap screw type one that came with the van. I do have one question please? Once I raise up the vehicle , where is the best place to put the jack stand? I know, probably a stupid question, but I was hoping to get a suggestion from someone way more knowlegable than me, before I do something that damages the car. Thanks again for the help!

Homer

Not sure which year you have, here's the manual for a 2005 Chevy Venture

See page 5-74 in the Service and Appearance Care section for the jack points.

http://www.extendedgmwarranty.com/owners-manual/chevrolet/2005-Chevrolet-Venture.pdf
 
I do not like bottle jacks, as the surface area where it contacts your car is very small and it may slip. I prefer floor jacks like this :

2hcorhd.jpg


( they are on special at Harbor Freight for $59 this month ) Always use jack stands. There are places where you can jack up your car, check in your manual.
 
Well, since we are talking floor jacks, and I've been laying under cars since I was 8 years old and I've had the same Lincoln 2 ton floor jack since 1991 without issue (knock on wood). I can assure you that not all floor jacks are created equal.

My Lincoln was "Proudly made in the USA", though sadly Lincoln started making their jacks in China at some point. They used to advertise that they were made in the USA with pride, etc.

A good floor jack is a thing of beaty - but you need to pay for it. My jack has paid for itself a number of times over over the years. And it's tough as nails.

Here is a good link describing the jacks that are out there. (I would not buy either Rub's jack or Ceiling Cat's jack. I would only get pissed off.)

http://www.hyjacks.com/H2.HTM

http://www.hyjacks.com/H22.HTM

Personally, I'd go for the 2 ton Milwaukee
 
Thanks for the replies!

I do know where the jack points are on the van as I"ve used the jack that came with it before. What I'm wondering is, once I have the van jacked up, where should I place the jack stands? I'm pretty certain there's not enough room to put it right beside the hydraulic jack. I was thinking under the control arm?
 
There are a lot of videos on youtube on how to jack a car up.
 
Warning, when lifting up the drive wheels with those jacks, be sure to set the parking brake on and or block the wheels of the ones on the ground. I have a nice old steel floor jack, weights a ton, lol and once the car rolled back and slip off the jack, I see it rolling back and a second later, down it went.

Still gives me the chills thinking about it cause on that car- 2000 Century, I must have change the oil on it more then a few times without locking the back wheels, why it rolled back that one time I was changing the front brake pads on it, I don't know but down it went and it just rolled back a little ways
 
Thanks for the replies!

I do know where the jack points are on the van as I"ve used the jack that came with it before. What I'm wondering is, once I have the van jacked up, where should I place the jack stands? I'm pretty certain there's not enough room to put it right beside the hydraulic jack. I was thinking under the control arm?

Check this page and see if your van has similar support points for the jack stands

http://diy-auto-repair.wonderhowto.com/how-to/jack-up-chevy-venture-van-0134256/
 
Warning, when lifting up the drive wheels with those jacks, be sure to set the parking brake on and or block the wheels of the ones on the ground. I have a nice old steel floor jack, weights a ton, lol and once the car rolled back and slip off the jack, I see it rolling back and a second later, down it went.

Still gives me the chills thinking about it cause on that car- 2000 Century, I must have change the oil on it more then a few times without locking the back wheels, why it rolled back that one time I was changing the front brake pads on it, I don't know but down it went and it just rolled back a little ways

Yeah, must admit there has been more than 1 time I've been under a car working alone in the garage and thought, "hmm, hope this thing doesn't come down"

There's a neat creeper that I saw recently that I want to buy when I build my new garage.

Check this out:

http://creepex.com/Cr/Home.html
 
Its "safe" to craw under a car jacked up, just be certain if only half the car is lifted that the wheels on the ground are lock-even if you done it before and nothing happen. Parking brakes don't aways work good once the car gets old if the brake isn't used often, so a brick behind the wheels is good. I like doing both now, set the parking brake and block the wheel.

If its the drive wheel on the ground, the trans will hold it steady if its in park. Guess it would not hurt the block the wheels still. I don't but maybe I should
 
I prefer floor jacks to bottle jacks myself because you are more out of the way than bottle jacks. Lincoln floor jacks are good, but they're expensive and heavy. Check out Princess Auto for a hybrid aluminum and steel floor jack. They're usually around $100 for 2 ton. Sure they're made in China, but there's not really much to go wrong with them, just the seals. I know hardcore Bloomington Gold restorers that have used their cheap Chinese floor jacks for years without issue, so I think it's worth the gamble.

Ventures are unibodies, and you're supposed to jack on the creases of the unibody, but I prefer not to because if you jack a lot there, you end up folding the crease. I usually jack on the engine cradle for the front. The engine cradle is usually big enough you can put a jack and jack stand on it.

I think the Venture has a straight axle at the rear. If this is the case, I usually put the jack right at the centre of the axle and put the jack stands where the creases on the unibody are. The advantage of this is you have both rear tires off the ground at the same time, thus making the wheel change quicker.

This doesn't apply to your vehicle or jack, but if the car is too low to the ground, you can use a low profile jack to jack up on the centre of the a arms.
 
Yeah, must admit there has been more than 1 time I've been under a car working alone in the garage and thought, "hmm, hope this thing doesn't come down"

There's a neat creeper that I saw recently that I want to buy when I build my new garage.

Check this out:

http://creepex.com/Cr/Home.html

That's a great idea for the creeper. I don't use metal floor stands at all . Since I do all of my own oil changes and tire changes I made a set of blocks out of 2 X 4 's . Jack the car or truck up , slide them in and there's no chance of the vehicle slipping off .

Sometimes I'll jack the car up high enough , slide the blocks in but not lower the car down on the blocks . If the jack does fail the car lands on the blocks but I only do that on tire changes when I'm not under the vehicle . Blocking the wheels that are on the ground . You bet . Better to be safe then sorry .
 
I have a floor jack, even when I put the jack stand to prop up the car I will lower that jack till there is weight on the jack stands and then pump the floor jack up a bit to have two places where the car is supported.
 
I have a floor jack, even when I put the jack stand to prop up the car I will lower that jack till there is weight on the jack stands and then pump the floor jack up a bit to have two places where the car is supported.

That is fine but if 2 wheels are on the ground and not block or the brake on, they can roll back and tip over the jack stands and jack..I seen it happen first hand. The floor jack did not keep rolling with the car but the car frame slip off it...I would have been killed if I was under it at the time, was like 2 seconds from when it started to roll back till it went down

Wedged a brick or a block of wood behind one or both wheels !
 
Read this in a car forum and I am reposting herewith:



Good Day,


I feel that I must respond to this post for the sake of accuracy, the honor of my son and family name and also to attempt to save other lives.



Lynne and I are the parents of three sons, Frederick III, Christian, Parker and our "adopted sons", his twin brother Jordan, Dimitri and Dan - all "carguys".



As stated in the article....



"The 21-year-old died Friday after a BMW he was working on collapsed on him in the family garage. Fred Klorczyk said that a floor jack likely failed while his son (Christian) was under the car changing the oil."

Jeff Johnson did a great job on the article on our son, brother and friend and I thank him for that. Jeff was a true gentleman who talked to us for hours in our darkest times to get an accurate depiction of our son and family. However, and unfortunately we do not have it on tape, nor is Jeff a "gearhead" and doesn't really understand jacks, jackstands and multiple layers of safety. I never said, nor is it accurate to say "that a floor jack likely failed..."

Christian is an experienced mechanic who started working on cars and following Formula 1 when he was a small child. He and our whole family witnessed Ayrton "Magic" Senna die at Tamburello 15 years ago. Yes, Christian was only six at the time and he would wake all of us up at 6:30AM to watch the pre-race show in Italy on satellite.

Christian is a true car guy as are his brothers and friends. My business is in the most safety conscious market in the world - nuclear boats, nuclear ships and nuclear power plants. That mentality is my life - has been since I was a kid engineer out of school. Ask any of my employees how I feel about safety. They have the right to stop any job and call me at anytime as no one is to ever get injured on our jobsites. This naturally carried over to my homelife. By the way, my father was a large machine mechanic by trade and a "gearhead" by avocation. No one would use the wrong tools - we have them all and all are of quality. No one in my garage or driveway would ever go under a car with only a jack of any kind holding it up. The jack elevates the car, jackstands support at proper points while working underneath and the jack is removed to improve accessibility. Period. Block the wheels if necessary. Emergency brake on. Car in gear. A lift would be better but we just were not at that point in our lives yet.

Christian had the right front tire off so that he could shine his double halogen lights on the work area and see clearly. He also had that tire/wheel under the right front rotor as an extra measure of safety as is a habit of ours when possible. He had four ton Craftsman jackstands in use. Two were just bought at Christmas when I sent him to buy a new jack since ours is getting to be five years old. Hydraulic cylinders and seals degrade over time. He didn't buy the jack since he felt what Sears, etc., had were junk so he bought more four ton stands but without safety pins. I did not realize there were redundant safety stands until... it was too late.


Christian was using my father's creeper for the first time. He found the creeper when cleaning the garage over Christmas. When he applied torque to the ratchet handle to break the plug loose, he experienced the law of physics of "equal and opposite reaction". As the plug broke loose, the creeper did also in a direction opposite to the torque vector Christian applied. Some part of Christian's body, some part of the creeper, the mallet beside him, something - we have no video, just supposition and theory... tripped the right front jackstand lever inadvertantly from the underside and a ton of the BMW E46 3 series xi crushed his chest and his right cheekbone. He never took, or could even attempt to take a second breath. Death was immediate and painless. If I were beside him at the time this occurred I could have done nothing to save him. This has been verified by five friends of mine who are doctors. I used the floorjack Christian used to elevate the car to get the car off of him. It was parallel to the car just as he would place it when he removed it from the jackpoint. I had to engage the cylinder with clockwise rotation which tells me Christian removed it per proper procedure. I had the jack underneath and car off him in seconds. Jackstands were under before I crawled from under the valance while Lynne called 911. Lynne came under with me from the wheelwell and had a pulse on his neck. She said he it was strong. I was doing chest compressions and trying to get a verbal response until the EMTs got there. When I heard LIFESTAR waved off over the EMT radios I had a sick, sick feeling.


A critical factor, in my professional engineering opinion, is that the creeper raised his body 3.5" higher than it would have been if he would have been working on the concrete as he was used to. It also raised his head 4.5" higher as there is a foam pillow headrest. Both creeper caster wheels at the head position were sheared from the creeper. I can only wonder that if Christian did not use the creeper would he have had the jackstands that high, would the energy at 9.8 m/sec squared have been decreased to a minimum so that if the freak accident happened he would have been injured less, would the extra measure of the tire under the rotor have saved his life without the extra creeper height, would he be alive today? Only God knows.


Christian is a fine, fine man who was known for his smile, intelligence, passion and willingness to help anyone at anytime... just like all of his brothers and "adopted brothers". The five of them and myself were his pall bearers. He would have it no other way. We were that close.


Also, to my fellow "carguys" and "gearheads", please learn from this tragedy. Scrap your cheapo jackstands... do your research, find the best jackstands there are, use the secondary and tertiary safety factors, do not fall to the temptation of human nature and operator error - use the extra safety factors! It may save your life, or maybe the life of you son. Had I would have known such Christian would be with us today.


Lastly, if you want to drive fast please do not do it on the road. Racetracks are readily available for that adrenaline rush we all crave. Track days with instructors are cheap and you are protected far more than


Godspeed Christian! May you be driving God's Veyron for him.


Please feel free to cut and past this article anywhere you think it may prove valuable to fellow "carguys". I pray that none of you ever suffer such a tragedy. May God Bless you all.
Link:

http://forums.bimmerforums.com/forum/showthread.php?p=21631982#post21631982
 
Light cars are MORE dangerous cause they can slip or be pulled off the jack stands easier. U have to be more careful working on smaller cars I have been told and it does make sense.

My floor jack is from 1978, lol...its never failed-just let go but has slip and tip over.

I like giving the car a hard shake before crawling under it and I use towels to lay on, no creepers for me..they are nice thou but yeah you can move to easy with a creeper. If I had a weak back I guess I would have one.

When I was in my 20's, I pulled rear wheel drive trans out with 4 jack stands and a floor jack--that same 1978 jack to lower the trans. Everybody thought I was crazy for doing it but I saved $250 pulling the trans and installing it myself--when I was in my 20's that was lots of cash...plus my car didn't have to go to the trans shop, I just threw the trans in a trunk of another car and drop it off and pick it up a few days later on.

We had somebody around here get killed working under his car this last summer, it happens every year like...all ages, young and old. I still change my oil but no more pulling out trans, lol
 
Read this in a car forum and I am reposting herewith:



Good Day,


I feel that I must respond to this post for the sake of accuracy, the honor of my son and family name and also to attempt to save other lives.



Lynne and I are the parents of three sons, Frederick III, Christian, Parker and our "adopted sons", his twin brother Jordan, Dimitri and Dan - all "carguys".



As stated in the article....



"The 21-year-old died Friday after a BMW he was working on collapsed on him in the family garage. Fred Klorczyk said that a floor jack likely failed while his son (Christian) was under the car changing the oil."

Jeff Johnson did a great job on the article on our son, brother and friend and I thank him for that. Jeff was a true gentleman who talked to us for hours in our darkest times to get an accurate depiction of our son and family. However, and unfortunately we do not have it on tape, nor is Jeff a "gearhead" and doesn't really understand jacks, jackstands and multiple layers of safety. I never said, nor is it accurate to say "that a floor jack likely failed..."

Christian is an experienced mechanic who started working on cars and following Formula 1 when he was a small child. He and our whole family witnessed Ayrton "Magic" Senna die at Tamburello 15 years ago. Yes, Christian was only six at the time and he would wake all of us up at 6:30AM to watch the pre-race show in Italy on satellite.

Christian is a true car guy as are his brothers and friends. My business is in the most safety conscious market in the world - nuclear boats, nuclear ships and nuclear power plants. That mentality is my life - has been since I was a kid engineer out of school. Ask any of my employees how I feel about safety. They have the right to stop any job and call me at anytime as no one is to ever get injured on our jobsites. This naturally carried over to my homelife. By the way, my father was a large machine mechanic by trade and a "gearhead" by avocation. No one would use the wrong tools - we have them all and all are of quality. No one in my garage or driveway would ever go under a car with only a jack of any kind holding it up. The jack elevates the car, jackstands support at proper points while working underneath and the jack is removed to improve accessibility. Period. Block the wheels if necessary. Emergency brake on. Car in gear. A lift would be better but we just were not at that point in our lives yet.

Christian had the right front tire off so that he could shine his double halogen lights on the work area and see clearly. He also had that tire/wheel under the right front rotor as an extra measure of safety as is a habit of ours when possible. He had four ton Craftsman jackstands in use. Two were just bought at Christmas when I sent him to buy a new jack since ours is getting to be five years old. Hydraulic cylinders and seals degrade over time. He didn't buy the jack since he felt what Sears, etc., had were junk so he bought more four ton stands but without safety pins. I did not realize there were redundant safety stands until... it was too late.


Christian was using my father's creeper for the first time. He found the creeper when cleaning the garage over Christmas. When he applied torque to the ratchet handle to break the plug loose, he experienced the law of physics of "equal and opposite reaction". As the plug broke loose, the creeper did also in a direction opposite to the torque vector Christian applied. Some part of Christian's body, some part of the creeper, the mallet beside him, something - we have no video, just supposition and theory... tripped the right front jackstand lever inadvertantly from the underside and a ton of the BMW E46 3 series xi crushed his chest and his right cheekbone. He never took, or could even attempt to take a second breath. Death was immediate and painless. If I were beside him at the time this occurred I could have done nothing to save him. This has been verified by five friends of mine who are doctors. I used the floorjack Christian used to elevate the car to get the car off of him. It was parallel to the car just as he would place it when he removed it from the jackpoint. I had to engage the cylinder with clockwise rotation which tells me Christian removed it per proper procedure. I had the jack underneath and car off him in seconds. Jackstands were under before I crawled from under the valance while Lynne called 911. Lynne came under with me from the wheelwell and had a pulse on his neck. She said he it was strong. I was doing chest compressions and trying to get a verbal response until the EMTs got there. When I heard LIFESTAR waved off over the EMT radios I had a sick, sick feeling.


A critical factor, in my professional engineering opinion, is that the creeper raised his body 3.5" higher than it would have been if he would have been working on the concrete as he was used to. It also raised his head 4.5" higher as there is a foam pillow headrest. Both creeper caster wheels at the head position were sheared from the creeper. I can only wonder that if Christian did not use the creeper would he have had the jackstands that high, would the energy at 9.8 m/sec squared have been decreased to a minimum so that if the freak accident happened he would have been injured less, would the extra measure of the tire under the rotor have saved his life without the extra creeper height, would he be alive today? Only God knows.


Christian is a fine, fine man who was known for his smile, intelligence, passion and willingness to help anyone at anytime... just like all of his brothers and "adopted brothers". The five of them and myself were his pall bearers. He would have it no other way. We were that close.


Also, to my fellow "carguys" and "gearheads", please learn from this tragedy. Scrap your cheapo jackstands... do your research, find the best jackstands there are, use the secondary and tertiary safety factors, do not fall to the temptation of human nature and operator error - use the extra safety factors! It may save your life, or maybe the life of you son. Had I would have known such Christian would be with us today.


Lastly, if you want to drive fast please do not do it on the road. Racetracks are readily available for that adrenaline rush we all crave. Track days with instructors are cheap and you are protected far more than


Godspeed Christian! May you be driving God's Veyron for him.


Please feel free to cut and past this article anywhere you think it may prove valuable to fellow "carguys". I pray that none of you ever suffer such a tragedy. May God Bless you all.
Link:

http://forums.bimmerforums.com/forum/showthread.php?p=21631982#post21631982

Something's not right here.

I think complacency and operator error is the cause of his demise. All the jack stands I've used can't have their lever "tipped" if the full weight of the car is on it.

Article also said he DIDN'T buy a new Craftsman jack since he thought they were junk. Well I'm betting it was better than the 5 year old jack he was using.