Home Renos... Looking for Tips

Hardwood can go over concrete if it isn't a basement floor. I wouldn't bother drilling into the concrete - just fasten the track to the hardwood with short screws since there isn't much lateral force.
Be sure it's hardwood and not just a thin laminate floor though.

Yeah you're right, I keep assuming that in a home, people are referring to their basement floor......(and you know what happens when you assume? lol)

That's a good idea gar, about using the plywood guide. You could even put double faced tape on one side if you're alone. With light pressure that'd work like the cat's ass......You should write that into "ask this old house", you'd prolly win a prize for that idea.....
 
OK, here's how I prevent my drill bit from skating when I drill tile. I drill a hole, just slightly larger than my diamond bit into a scrap piece of plywood. Then place the plywood over the spot where you want the hole. The plywood guides the drill bit and prevents damage to the tile. It helps to have a somebody hold the template while the other drills. I've done this with small 3/16th and larger 1.5 inch bits.
I keep the plywood templates in my drill case for future use.

Finally, someone who actually knows what they're doing. The amount of misinformation on TERB is unbelievable! Cannot imagine why anybody would ask for advice on anything in this place.
 
Finally, someone who actually knows what they're doing. The amount of misinformation on TERB is unbelievable! Cannot imagine why anybody would ask for advice on anything in this place.

because if he didn't, he wouldn't have gotten that great idea that you are praising.......doh.....
 
Oh, and I guess every contractor with half a mind is an idiot for using a hammer drill to drill holes into masonry......

You can drill into concrete without using a hammerdrill. It just takes a lot longer and probably wears out the bit faster (due to heat buildup).

There is a big difference between a contractor who drills lots of holes into concrete vs. a homeowner who needs to drill only a few.

The homeowner would be an idiot to buy a hammerdrill that he will only use once. The contractor would be an idiot not to buy one (or more depending on the size of the crew).
 
Just remember: there's a difference between CONCRETE and CEMENT.....I can see you being able to drill into cement, a cement block, mortar, or brick without a hammerdrill.....but into 50 - 100 PSI concrete? LOL OH kay.......you can start now, and I'll check back on you on Monday to see how deep you are, how many bits you've gone through, and how often you've returned your drill since you keep burning it out.......

But then again, I digress, anything is possible if you want it bad enough...I mean heck, they put a monkey into orbit didn't they? It only cost a billion dollars and took years.......
 
Just remember: there's a difference between CONCRETE and CEMENT.....I can see you being able to drill into cement, a cement block, mortar, or brick without a hammerdrill.....but into 50 - 100 PSI concrete? LOL OH kay.......you can start now, and I'll check back on you on Monday to see how deep you are, how many bits you've gone through, and how often you've returned your drill since you keep burning it out.......

But then again, I digress, anything is possible if you want it bad enough...I mean heck, they put a monkey into orbit didn't they? It only cost a billion dollars and took years.......

I have drilled into concrete floors and while I would certainly prefer a hammerdrill it can be done without one. But I'm only talking about drilling in for small tapcons and/or lead anchors. If we're talking about drilling out for a 1/2" bolt or larger than I certainly agree you'll be there forever w/o a hammerdrill.
 
Go and ask her at the store, she will tell you how to do it. Or do like I did and get her to do it for you. While she was on her hands and knees, I pulled her thong to the side and gave her a drilling!


339oi6t.jpg
 
When the sliding doors were originally installed they were drilled into the concrete floor. It's not in the basement. So that's why I want to put them back the way they were. Good point about checking the height because before they were on carpet and now they'll be on hardwood. I don't think there will be a problem with height though (I can adjust the height of the rollers). They hang off the top track and the bottom track guides the rollers. I'm a little concerned about drilling into the same holes in the wall and not getting a good grip...

I'm planning on using the tape option for the tile and I've already bought a tile bit. I know it could take a while but it's only a couple holes so I'm not worried.
 
Do you not need to also wet the bit for drilling ceramic to ensure less friction which ensures less chance of breaking?

I am just a girl, so I may be wrong.

Kya...don't ever say "I JUST A GIRL"...we have done many reno's around our house and my wife is in there like a dirty shirt....she comes up with ideas that I may not go with at first...then when I do it my way, I think...."DAM shoulda listened to her":rolleyes:

Besides there is nothing sexier than a woman in a tool belt!!!!
 
Kya...don't ever say "I JUST A GIRL"...we have done many reno's around our house and my wife is in there like a dirty shirt....she comes up with ideas that I may not go with at first...then when I do it my way, I think...."DAM shoulda listened to her"

Besides there is nothing sexier than a woman in a tool belt!!!!
huge.38.191812.JPG