drywall for easy electrical & plumbing access ?

If you are building or renovating the place now, the easiest thing to do is plan ahead. Run twisted pair, coaxial, quad, Ethernet, and other wire and cables. Route the wires through a closet with an access panel. If you know where the wires are run in the walls, you can cut a hole in the sheet rock and access them for use. You can minimize the damage to some small holes to access the wires. if you have to, you can make a temporary wood cover to conceal the holes till your next paint job
 
Drywall is cheap to repair. I never understood why people would waste hours of labour trying to fish a cable without damaging it.

Bash the wall or ceiling where you need to and get the job done right and a lot faster. Pay a dry waller with the money you saved by not wasting hours of labour to repair the damage.
In fact, get the electrician or plumber to tell you where they need access, set your saw at drywall depth and cut them decent access for the entire route (they can hold the vacuum nozzle), instead of making them bash a bunch of crude little holes. The material to fill the cut's cheap, and the labour will likely be the same or less than the same patching of hole after hole after hole after…. But like you say, drywallers don't charge what plumbers and electricians do.
 

Repairing the holes is not that difficult. It is the time and expense of repainting the room.
 
Drywall is cheap to repair. I never understood why people would waste hours of labour trying to fish a cable without damaging it.

Bash the wall or ceiling where you need to and get the job done right and a lot faster. Pay a dry waller with the money you saved by not wasting hours of labour to repair the damage.


Exactly, just finished installing several new pot lights in an existing residence and punched holes along the way to run the wires, then used patching technique shown in Ceiling Cat's video and voila, installed 20 lights in less than 3 days, saved lots of money.
 
Drywall is cheap to repair. I never understood why people would waste hours of labour trying to fish a cable without damaging it.

Bash the wall or ceiling where you need to and get the job done right and a lot faster. Pay a dry waller with the money you saved by not wasting hours of labour to repair the damage.

True, however, on the flip side:

1. Huge mess

2. Patching Drywall is an art. Specifically once it's done that it's invisible.

3. To do properly, you have to go stud to stud, or joist to joist - that's 16". Then feathering out the compound, you have to go at least another 2 feet on either side.

4. Large areas.

5. Divorce Dust.
 
True, however, on the flip side:

1. Huge mess

2. Patching Drywall is an art. Specifically once it's done that it's invisible.

3. To do properly, you have to go stud to stud, or joist to joist - that's 16". Then feathering out the compound, you have to go at least another 2 feet on either side.

4. Large areas.

5. Divorce Dust.

Not that hard to do...not necessarily a huge mess, and no, you don't have to go stud to stud, and no, you don't need to feather out 2 feet. But...it is an art, and as another poster said, the bigger issue is repainting and/or matching paint.
 
Not that hard to do...not necessarily a huge mess, and no, you don't have to go stud to stud, and no, you don't need to feather out 2 feet. But...it is an art, and as another poster said, the bigger issue is repainting and/or matching paint.

I guess I've been doing it wrong all these years going stud to stud.

Then again, I do like to do it right.
 
I guess I've been doing it wrong all these years going stud to stud.

Then again, I do like to do it right.

Depending on the size of the hole, I've just slipped in a couple pieces of 1x2 longer than the hole and screwed it to the existing drywall, then screwed the patch to the wood. Works okay, but certainly not as strong as going across to the studs. For bigger patches I will cut out to the edge of the studs, then screw some 2x2 to the side of the stud and then patch. Easier and quicker than trying to trim the drywall along the middle of the studs I think.