What do you look for in a grinder?

frankcastle

Well-known member
Feb 4, 2003
17,866
249
63
Looking to removed a sealed off furnace pipe..... upgraded to a high efficiency one that goes out the side of the house.... leaving a completely useles metal column going through my house. Already removed the dry wall. Thinking about getting back a little space (not much but hey an extra shelf per floor is not bad).

Anyways, I assume a grinder is what I want and I figure I'll probably use it a few more times here and there so

What brand, how much power, and type of attachment do I need?
 
is the b vent capped off on the roof? otherwise any rain etc can run down and leak into the house.
The pipe is in sections and twists apart, you should be able to dismantle it without any tools per say . it is double walled, the outer is galvanized & the inner is aluminum (Providing it was for a gas furnace)

Ask my neighbor about using a grinder to cut off metal inside the house while doing renos.... ended up with a $100,000 repair from the fire and moving out for 3 months while repairs were done . a better choice is a reciprocating saw or otherwise known as a sawzall (brand name) with a fine metal blade .
I would be very careful using a grinder indoors for reason mentioned.

http://t1.gstatic.com/images?q=tbn:ANd9GcSZBlmqoUMmdO00Zylf6IUiOqDGJvZKk9wgdqErqJ304e9aAo_uLA
images
 
I thought it was the ultimate CG :D At least this evil looking thing is not involved.............


51c9oh.jpg
 
Thanks Ben,

I had roofers cut the tops off and seal in the exhaust pipes on the roof.

Good point about sparks. I watched a few safety vids on the topic and I'm leaning towards a drill and tin snips.

But upon closer inspection the furnace pipe does have screws and looks like I could take it apart.

The fireplace flue which I didn't mention looks more solid.

And for all you other people...... get your minds out of the gutter! :D
 
As far as what grinder to buy, For what you are describing, a 4" Dewalt or Mikita should do nicely. As with most tools, you get what you pay for.

You want to use what I call a "zippy cut" wheel. It's more of a cutting blade than a grinder stone disk.

It will cut right through the steel like a hot knife through butter.
 
As far as what grinder to buy, For what you are describing, a 4" Dewalt or Mikita should do nicely. As with most tools, you get what you pay for.

You want to use what I call a "zippy cut" wheel. It's more of a cutting blade than a grinder stone disk.

It will cut right through the steel like a hot knife through butter.

Thank you JTK,

I ended up buying a tin snip and a 3/4" black oxide drill bit.

The area is dry and wooden, I'm a bit freaked out that sparks might start a fire. Only time I used a grinder was for cutting lag bolts out of the outside of my house where a deck used to be. It got very hot and tons of sparks.

Anyways, happy that the snips should be faster than a hacksaw but not as risky as a grinder (or costly).

I'm not goint to lie, a graphic safety video about grinders with no guards and blades of teh wrong rpm freaked me the fuck out.
 
You have to try pretty hard to light wood on fire with a grinder. The sparks just cannot stay hot enough long enough to start a fire. (Unlike a cutting torch or arc welder where the dripping molten metal will stay hot enough long enough to definitely light up a piece of wood.)

And yes, grinders are definitely dangerous if handled improperly, or without the guards. They can grab and twist out of your hand and cut you very quickly. Sometimes when using a grinder it just isn't possible to use grab handle and you try to hold on to the body of the grinder and it's easy to have an accident.
 
thought this was a thread about lap dancing

Me too actually!

reciprocating saw is the best way to go if you can't pull apart the B-vent. A 4" grinder is very handy but lot's of sparks...I've had a B&D Pro for many years and has served me well! I use very thin 'zip-cut' type cutting disks with a spacer instead of grinding disks since grinding disks are for, well, grinding! The thin disks are designed for cutting and produce less sparks/molten metal. It takes a steady hand though as they can break off easily. Make sure you're wearing proper clothing and a face shield as you may end up with debris embedded in your eyes, face, arms, etc. Always, always work safe!