drywall for easy electrical & plumbing access ?

odie999

Member
Mar 14, 2010
395
12
18
yet still keep the drywall cheap?

by "easy access" I do NOT mean "it's easy to hammer that shit to bits & get behind it"

If not, are there drywall alternatives that are not really, really expensive (still maintaining easy access)
 
The main reason sheet rock is use is for fire proofing. Sheet rock is made from crushed gypsum mineral that is then heated and turned into a gypsum slurry that is formed and then dried into sheet rock. Sheet rock is a very fire resistant material. The way it is installed also helps prevent fire from spreading. The sheets have to be butted up against each other and then sealed and sanded smooth not to allow flames to consume the wood frame studs in the event of a fire. I have never seen removable panel wall in permanent home construction. Removable panel walls are used in temporary construction and mobile homes.
 
Never seen an access panel for a whirlpool tub?

Neither of us is talking about the small metal doors.

I'm asking about ways that make it easy to access an entire wall's innards - taking all the drywall (or other fireproof alternative) off easily
 
I think the only way to meet code is to use sheet rock.
 
Thanks for the reply

there's also the added benefit that screwing the drywall in increases a wall's tortional stiffness and strengthens the eintire structure. If you don't screw it in you lose some of that strength benefit.

The main reason sheet rock is use is for fire proofing. Sheet rock is made from crushed ... . Removable panel walls are used in temporary construction and mobile homes.

I was hoping something different has come along in the last few years, or there's a specialized technique I never heard of.

It's kind of funny to me ... it's furniture & carpet & drapes that start and feed fires. If these were designed to be more fireproof (and if we had really cheap sprinkler systems) we'd have a lot fewer fires.
 
Put the wiring, heating ducts and plumbing outside the wall, makes it easier to access.
 
Thanks for the reply




I was hoping something different has come along in the last few years, or there's a specialized technique I never heard of.

If you have an unfinished basement ceiling, you may be able to make a conduit tube that runs parallel to the joist to facilitate passing of wires when require. To access the conduit, you can use suspended ceiling panels or a hybrid ceiling of sheet rock with a row of suspended ceiling tiles along the walls. This conduit can give you access to wiring in the basement as well as on the upper floor.

It's kind of funny to me ... it's furniture & carpet & drapes that start and feed fires. If these were designed to be more fireproof (and if we had really cheap sprinkler systems) we'd have a lot fewer fires.

If you gave me some specifics, maybe I can give you some ideas.
 
You can build a wainscot paneling with removable panels.

34tcuut.jpg
 
If you gave me some specifics, maybe I can give you some ideas.

No specific project pending, just wanted to see what's out there ... a relative had a house built for him to order and he's always taking stuff apart to change stuff. One time he put in 20 amp wiring and another time fiber optic cable. He thought he needed more performance than wireless.

It's always a major operation.
 
In that case you may be interested in using steel studs. Installed properly all the access holes fall in line and therefore you don't have to tear out huge sections of drywall to fish a line horizontally. The downside is that steel studded walls are not structural.

They do make structural steel studs. You have to use a chop saw to cut them.
 
one option is to build a chase for the wireing and mechanical.It is a rectangular recess built into the house that the mechanical electrical plumbing run through . Usually they get hidden in closets vertically and in the joist spacing for horizontal . With some access paneles you can work on the sytems you need
 
If you had a closet stacked on top of each other you could build a conduit to fish wires through. You can also build conduit parallel to your joist. This is not perfect, but it is a lot better than tearing up your walls. this way you need to do minimal work.

You will have to be careful not to pass wires with high voltage near low voltage wires to minimize interference.



 
You can build metal access panels like this in closets to access your wiring, I have seen them as big as 24 in. by 24 in.

90d8uo.png
 
You'll need to watch a bunch of late-night infomercial stuff on OTA channels to find it, but there is a pre-finished, removeable panel system that's attractive and affordable (so they say) with a local TO outlet. I'd be willing to bet the cost is something like: finished drywall + cost of opening and repair, so it wouldn't pay off until the second use.

I'd go with the pre-built chase method, especially for planned new construction, especially if you're planning work in the basement. Essentially every suspended ceiling is a chase. If you can't stand the look, at least do something like a lighting valance or false beam that can hide the services you want to add later. Baseboards can do a similar job, but do be mindful as the Cat above has warned that they want drywall behind them to meet code.
 


If you were to bump out the wainscot 3 or 4 inches in front of the sheetrock you will have a cavity to install your electrical, electronics and plumbing.

IMO for all the expense and time you would have to go through you may as well go the usual way and it would all be the same in the end.
 
Drywall is cheap to repair. I never understood why people would waste hours of labour trying to fish a cable without damaging it.

Bash the wall or ceiling where you need to and get the job done right and a lot faster. Pay a dry waller with the money you saved by not wasting hours of labour to repair the damage.
 
Alternatives always seem to look shitty...joints every 4 ft, etc. If you want a continuous wall with no visible screws, etc. then plaster or drywall are your options.

Access can be planned before hand...if that is a concern, by putting in empty conduit to some accessible location.