I need to shoot screws into a wall

gypsyluver

New member
Oct 7, 2008
43
0
0
I am looking for a devive or a machine that will shoot 1'' metal screws into my living room wall to hang up a few shelves and a gun rack .i dont want to use nails...i need to shoot screws into a wall to hang these up...is there anything that will shoot screws?
 
I am looking for a devive or a machine that will shoot 1'' metal screws into my living room wall to hang up a few shelves and a gun rack .i dont want to use nails...i need to shoot screws into a wall to hang these up...is there anything that will shoot screws?
What about an electric screw driver, these are after all screws.
 
don't u need these stupid special ones that open up inside?
 
You don't "shoot" screws.

You have to screw, (twist) screws in since they are threaded.

You can shoot nails in, but you state that you don't want to use nails. Fine.

Locate the studs (use a studfinder which is 50 / 50 at best) or poke a few nails to find the stud. Typically studs are spaced at 16" c/c. Mark your holes, , predrill the holes for the screws (slightly smaller than the diameter of the srew) and screw away. You can use your hand (what I would do for job like this) or get a chordless drill with correct bit.
 
Make sure the screws are going into studs. Studs should be 16" on center. Use a stud finder if you have to. Any drill will work with the right size screwdriver head. If you don't want to buy one you can probably rent one at your local tool rental store.
 
and for the record: you'll need longer than 1" screws.....if they are going through something, then into the wall you won't have enough penetration into the stud to hold a tea cup.

Since you're hanging a gun rack you'll need at least 1 1/4" #8. Remember: the dryall itself is 1/2" at least........
 
Is it simply a gun rack or a cabinet that can be locked?

It would be easy for a burglar to pry the whole thing off the wall if it's only screwed on, you should consider using stronger lag bolts.
 
ok so i need longer screws...for the shelves in gunrack...i have a drill but do not wish to use it...ik would rather shoot them in with a ramset gun or hilti gun/...if not ill just get a electric drill to shoot them in
 
The very point of using screws is that because they are screwed into the wood (stud) they provide greater resistence to being pulled out than would ridged nails pounded or shot into the wood.
 
ok so i need longer screws...for the shelves in gunrack...i have a drill but do not wish to use it...ik would rather shoot them in with a ramset gun or hilti gun/...if not ill just get a electric drill to shoot them in

ummmm a ramset or hilti powder activated fastner would probably shoot through the back of the cabinet and right through the stud, since they are made to go through steel and into concrete......:eek: even with the lowest power yellow tips they still wouldn't hold as well as screws or lags.....
 
ok so i need longer screws...for the shelves in gunrack...i have a drill but do not wish to use it...ik would rather shoot them in with a ramset gun or hilti gun/...if not ill just get a electric drill to shoot them in

As has already been mentioned, you cannot "shoot" screws. They have threads and need to be screwed in, either with a screwdriver or a drill.

You still did not say what type of material you are trying to mount your shelves on/into. There have been a number of suggestions if it is drywall or plaster on studs, and if it is concrete, you may need some type of tapcon screw.
 
Is this thread a joke, or are you one of those guys who doesn't even know which end of the hammer is which? (I'm mid 40's and I am always AMAZED at the number of men my age (younger is even worse) that don't have the slightest inclination towards being able to fix something themselves. Can't change a fuse (I've met 2), can't change a tire (met more than I can count), can't fix a leaky faucet, etc. etc. etc.)

As tboy stated, you will fire that ramset right through the wall. :eek:

It's not hard work to screw anything into a stud wall.

What I'm now wondering is what is this going to look like when it's done. I can just picture some gun rack an inch out of level, with screw holes everywhere, broken drywall, cracked / scratched all to hell wood on the rack, and screws sticking out half an inch with no consideration as to hiding the ends of the screws.
 
don't u need these stupid special ones that open up inside?

Most likely you are referring to butterfly wing nuts that open up on the inside of the drywall, these are good also if you can't hit the studs...although you don't "Shoot" these either'
Pretty sure there's nothing that shoots screws as I have most tools known for this kind of work.
Go for the stud finder and use good srews, use the wing nuts if nessesary but be sure of what you are doing
If this cabinet and gun weights a bit you better have a good connection
OR....:eek:
 
Is this thread a joke, or are you one of those guys who doesn't even know which end of the hammer is which? (I'm mid 40's and I am always AMAZED at the number of men my age (younger is even worse) that don't have the slightest inclination towards being able to fix something themselves. Can't change a fuse (I've met 2), can't change a tire (met more than I can count), can't fix a leaky faucet, etc. etc. etc.)

As tboy stated, you will fire that ramset right through the wall.

It's not hard work to screw anything into a stud wall.

What I'm now wondering is what is this going to look like when it's done. I can just picture some gun rack an inch out of level, with screw holes everywhere, broken drywall, cracked / scratched all to hell wood on the rack, and screws sticking out half an inch with no consideration as to hiding the ends of the screws.

Evidently Captain Kirk knows how to screw but the OP doesn't. :cool: LOL!!!
 
ok so i need longer screws...for the shelves in gunrack...i have a drill but do not wish to use it...ik would rather shoot them in with a ramset gun or hilti gun/...if not ill just get a electric drill to shoot them in

Better still, just stick a screw into your shotgun and blast away!! lol. What you need are heavy duty drywall mounts...unless you are mounting on poured concrete...in what case you just need a set of concrete fasteners.