Anyone ever use a clay bar?

bazokajoe

Well-known member
Nov 6, 2010
11,101
10,232
113
I own a white truck with a ton of little rust looking spots all over it.I was told by the dealer they were caused by brake pad dust sticking to the paint then oxidizing.
They told me to buy a clay bar and rub it over the surface to remove these rust spots.
Has anyone tried this product on their vehicle?
I watched a video on how to use it.Seems to work.
 
I've used one on my car every spring to get the salt and crap off the car. Works really well and you would be amazed at how dirty the clay ends up. Usually stick to Meguairs clay and use meguairs quick detailer as the lube.
 
You can get them at Canadian Tire. A good alternative is to use a fine polish ( finer grit than compound ) I use an orbital polisher to buff off all the dirt and bring the surface to a glass like sheen. It is a good idea to take off the crap that adheres to the lower part of the sides of the car with bug and tar remover.

ucajs.jpg


They are a real time saver for polishing and waxing a car.
 
Last edited:
Clay bar is avaliable at can tire. I used water with a little soap instead of buying their product. It just helps the bar to glide over the surface instead of getting stuck. What ever you do dont drop the bar on the ground cause you dont want the dirt in the bar. When it gets dirty fold it over and get a clean spot. Run your fingertips over the paint to feel the embedded material in the paint surface so you know when it is clean.
 
You can get them at Canadian Tire. A good alternative is to use a fine polish ( finer grit than compound ) I use an orbital polisher to buff off all the dirt and bring the surface to a glass like sheen. It is a good idea to take off the crap that adheres to the lower part of the sides of the car.

ucajs.jpg


They are a real time saver for polishing and waxing a car.

Suggesting a novice use a polishing compound and orbital polisher is a bad idea. He'll burn or break through the paint because of his lack of experience.

Hand polishing is time consuming, but there's less chance of making a mistake.
 


NO no NO DO NOT LISTEN

No, no NO do NOT listen

A clay bar does not abrade your paint surface. Polish is an ABRASIVE and creates microscopic scratches in your paint. In the case of a white paint job, those microscopic scratches can get stained in the "grooves" and cause visible discolouration. IF you do use an abrasive polish it is important to use a good wax/sealer to fil and protect those microscopic scratches.

A clay bar acts more like a lint roller for paint. It glides over the surface on a liquid lubricated film and any little bits that stick up from the surface of the paint, get stuck and imbedded harmlessly in the soft clay bar .

So, from the sounds of it, your paint feels rough which indicates that there is a surface contamination on the surface. NOT in the paint like a stain or a scratch.

So use the clay bar as directed first. I bet it fixes your problem.

Good example to ignore anything written in RED COMIC FONT except where to buy cheap toilet paper by the bale. Appropriate Ceiling Cat is an expert on bulk purchases of toilet paper considering he is so full of shit ! LOL!


Agreed, use the clay bar. It works and will not hurt the paint. Ever drive by somebody on the road and their cover is covered with swirl marks? You don't want to be that guy.

R2R
 
Suggesting a novice use a polishing compound and orbital polisher is a bad idea. He'll burn or break through the paint because of his lack of experience.

Hand polishing is time consuming, but there's less chance of making a mistake.Just use common sense, apply a light coating of fine polish ( not compound ) and buff off with the random orbital polisher. You would have to be an idiot to screw that up.

You are thinking of a car polisher, a random orbital polisher is very easy to use. It is very simple, apply a thin coating of fine car polish and buff off with the random orbital polisher. It is not hard to do, if you do it correctly like in the video you will get a glass like sheen on your car.

 
He's not asking how to shine his truck to a nice "sheen". He wants to remove particles of rust from brake pads. From what I know bazooka, clay bars work. How long have these particles been on the paint though? That could be the determining factor on how effective the clay bar is.
 
I've used clay for many years. It's incredible how well they work. Just be careful to make sure your surface is adequately lubricated. Some clays require quick detailer to work; others will work with simply water or diluted car wash.

Suggesting a novice use a polishing compound and orbital polisher is a bad idea. He'll burn or break through the paint because of his lack of experience.

Hand polishing is time consuming, but there's less chance of making a mistake.

What CC said. A random orbital is very easy to use. You'd really have to work hard to screw it up, and it's near impossible to burn through paint (given the double clutch).

Where can you buy these clay bars?

Canadian Tire has the Meguairs. But www.eshine.ca will have more more, including random orbitals. For clay, I can highly recommend the Riccardo yellow.
 
I've been using a clay bar on my cars for years. I try to stick to Meguairs as it is easlity available (even walmart has it). There are lots of providers of clay bars and with various qualities and some with sime abrasivebness. Meguaires has very little abrasision and is relativly cheap for a first try.

I also had a white car that had rail dist. The car was shipped on a train and the wheels / rails of the train left small metal dust on the car that rusts. Your dealer is telling you the accurate truth and a clay bar is what you need. My first try took the little rust spots right out.

Polishing will only make things worse as the paint is softer than the metal flakes and will create small bumps too.

Suggest you wash your car really well. Then clay it. Then put onn a good paste wax (carnuba) with an orbital poslisher and you will be a happy man. Remember the wax as the clay will remove any wax you may have left on your car. Unless you have oxidation there is no need to polish.
 
WOW! Thanks for all the great advice.Glad to know my dealer isn't screwing me around.I will let you know how it turns out.Hopefully it's nice out this weekend and I will do it.
 
He's not asking how to shine his truck to a nice "sheen". He wants to remove particles of rust from brake pads. From what I know bazooka, clay bars work. How long have these particles been on the paint though? That could be the determining factor on how effective the clay bar is.

Been on their for about 2 years.Probably make it harder for it to come off.
 
Polishing will only make things worse as the paint is softer than the metal flakes and will create small bumps too.

Wax only protects the surface, but protection means little if the paint itself is scratched up. Polishing is needed to make the car shine and remove defects (swirls and scratches).

Carnauba is great for depth of shine, but it isn't very durable. Car guys who don't mind a monthly wax will swear by it, but for the less inclined, synthetic is the more practical choice.

For our harsh winters, and for doing cars for my lazier friends/family, I use Collinite 476. The layer I put on last October is still beading now. Check it out.
 
Finally got around to using a clay bar on my car this weekend.Worked great.Thanks for everyones advice.